Skip to content
Sensors

2S 20A 8.4V 18650 Lithium Battery Protection Board/BMS Board Standard

৳140

The 2S 20A 8.4V 18650 Lithium Battery Protection Board (BMS) is the safety layer between a two-cell Li-ion pack and whatever it powers: it watches both cells and disconnects the pack on overcharge, over-discharge, overcurrent or a short circuit.

7.4V packs in RC cars, robots, power banks and portable LED builds are its usual place. Top-balancing at 4.2V keeps the two cells matched as they age, and the low standby drain leaves the pack healthy between uses.

  • 20A continuous discharge rating
  • Overcharge cut-off around 4.25-4.35V per cell, over-discharge around 2.7-3.0V with auto-release on charge
  • B+, BM and B- go to the cells; P+ and P- carry the protected output
  • Suits matched 18650, 21700 or 2S Li-po cells, on a PCB of roughly 50 x 20mm

Wire it in before the pack's first charge, and use cells of the same capacity and age.

এই part দিয়ে project — কেনার আগে ফ্রি চালিয়ে দেখো:Tekko Sim — free circuit & Arduino simulator

Configuration: 2 series Li-ion cells (2S, 7.4 V nominal, 8.4 V full charge)

Continuous Discharge Current: 20 A with adequate trace heat sinking

Overcharge Cut-off: approx. 4.25-4.35 V per cell

Over-discharge Cut-off: approx. 2.7-3.0 V per cell, auto-release on charge

Balance: top-balancing at 4.2 V, approx. 40-60 mA balance current

Protection: overcharge, over-discharge, overcurrent, short circuit

Cell Pads: B+ (pack plus), BM (series midpoint), B- (pack minus)

Output Pads: P+ / P- protected output to load and charger

Suitable Cells: 18650, 21700 or 2S Li-po with matched capacity

Standby Drain: very low quiescent current to preserve the pack

PCB Size: approx. 50 x 20 x 3.5 mm

Weight: approx. 5 g

CategorySensors
Model no.2S20A-BMS
AvailabilityIn stock
In stock9 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

5.0 out of 5 · 1 review

  • ★★★★★ Saleh Sayeem Verified buyer

Questions about the 2S 20A 8.4V 18650 Lithium Battery Protection Board/BMS Board Standard

What does a 2S BMS protection board do?
It monitors a two-cell Li-ion pack and disconnects it on overcharge, over-discharge, overcurrent or short circuit, while balancing the two cells so they age evenly.
How do I wire the board to my 18650 cells?
Solder B+ to the pack positive, B- to the pack negative and BM to the midpoint where the two cells join; the load and charger then connect to P+ and P-.
Can I charge the pack through this board?
Yes - charge through the P+/P- pads with a proper 8.4 V CC/CV Li-ion charger and the board handles the cell-level cut-offs and balancing.
What charger voltage does a 2S pack need?
Always an 8.4 V two-cell Li-ion charger; a single-cell charger or a generic adapter will not terminate the charge correctly.
Can it really deliver 20 amps continuously?
Yes within its design limits - keep the traces beefy, give the board some airflow, and size the cells so they can actually supply 20 A safely.
Can I use it with Li-po packs too?
Yes, any matched 2S pack of 18650, 21700 or Li-po cells with the same nominal voltage and capacity works the same way.
Does the board need cooling at high current?
For sustained draws above roughly 10 A keep the wiring short and thick, give the board airflow, and mount it away from the hottest cell for long life.
এই 2S BMS বোর্ডের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
বাংলাদেশে অনলাইনে কোথায় কিনবো?
Tekko অনলাইন স্টোরে এটি স্টকে আছে - সারা বাংলাদেশে হোম ডেলিভারি সুবিধা সহ অর্ডার করতে পারবেন।
লিথিয়াম ব্যাটারি প্যাকে এটা কেনো করবো কেন?
BMS ছাড়া 18650 সেল ওভারচার্জ বা ডিসচার্জে নষ্ট হয়ে যেতে পারে এমনকি বিপদজনকও - এই বোর্ড সেল দুটোকে নিরাপদ সীমার ভেতরে রাখে ও ব্যালেন্স করে।
সেলের সাথে কিভাবে লাগাবো?
আগে সেল দুটোর ভোল্টেজ মিলিয়ে নিন, তারপর B+ প্যাকের পজিটিভে, B- নেগেটিভে আর BM দুই সেলের জোড়া পয়েন্টে সোল্ডার করুন - লোড যাবে P+/P- প্যাডে।
পাওয়ার ব্যাংক বা ই-স্কুটার প্রজেক্টে কি চলবে?
হ্যাঁ - 20A রেটিংটি স্কুটার, রোবট, লাইট অ্যারে বা বড় পাওয়ার ব্যাংকের মতো হাই-ড্রেন 2S প্যাকের জন্যই উপযুক্ত।