Skip to content
Robotics

A4988 StepStick Stepper Motor Driver Module

৳170

A4988 StepStick stepper driver module, the small carrier that turns Step and Dir signals into precise motion in 3D printers, CNC rigs, plotters and camera sliders. It drives one bipolar stepper with microstepping down to 1/16, and the onboard trimpot sets the current limit, so the same board suits small frames and common NEMA 17 motors alike. It plugs straight into RAMPS and CNC shield sockets.

  • Microstepping: full, 1/2, 1/4, 1/8, 1/16
  • Motor supply 8 to 35 V DC, logic 3.3 to 5 V
  • About 1 A per phase without cooling, up to about 2 A with a heatsink and airflow
  • Enable, Reset and Sleep pins; over-temperature shutdown
  • Standard StepStick 16-pin footprint

Set the current limit before running a motor, and never plug the board in or pull it out while the motor supply is live.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Driver IC: A4988 bipolar stepper driver

Motor Type: One bipolar stepper motor per board

Microstepping: Full, 1/2, 1/4, 1/8, 1/16

Motor Supply Voltage: 8-35 V DC

Logic Voltage: 3.3-5 V typical

Current Output: approx 1 A per phase without heatsink, up to approx 2 A with active cooling

Current Setting: Onboard potentiometer (Vref)

Control Interface: Step and Dir inputs, plus Enable, Reset and Sleep pins

Protection: Over-temperature shutdown

Board Format: StepStick 16-pin layout for standard 3D printer and CNC shields

Cooling: Heatsink and airflow recommended above approx 1 A per phase

CategoryRobotics
Model no.A4988
AvailabilityIn stock
In stock3 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the A4988 StepStick Stepper Motor Driver Module

What is the A4988 StepStick driver used for?
It converts Step and Dir signals into the coil currents a bipolar stepper needs, which is exactly what 3D printers, CNC routers, laser engravers, camera sliders and robot joints require.
How do I wire the A4988 to an Arduino?
Connect VDD to 5 V and GND to ground, run STEP and DIR to two digital pins, tie RESET and SLEEP together, join the logic ground with the motor power ground, and hook the four motor wires to the 1A-1B and 2A-2B outputs.
How do I set the current limit?
Power the logic side first, measure the voltage between the trimpot wiper and ground, and turn the screw until Vref matches the limit your board's sense resistors specify for your motor's rated phase current.
Which motors work with this driver?
Any bipolar stepper that stays within the 8-35 V motor supply and your set current limit — typically NEMA 11 to NEMA 17 motors, and larger frames only if their rated current remains within the driver's capability.
Why does my driver or motor run hot, or skip steps?
The chip sheds heat through the small PCB, so above roughly 1 A per phase it needs a heatsink and airflow; skipping also happens when the current limit is set too low, the supply sags or the motor is accelerated too fast.
Can I use several A4988 boards on one controller?
Yes — RAMPS, CNC shield and similar carrier boards hold four or more sockets so the X, Y, Z and extruder axes each get their own driver.
Is this driver suitable for beginners?
Yes, provided you respect two rules: set the current limit before running and never connect or disconnect a motor while power is on, since both mistakes can kill the chip instantly.
A4988 ড্রাইভারের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, সিঙ্গেল বা একাধিক প্যাক দুইভাবেই নেওয়া যায়।
3D প্রিন্টারের স্টেপার ড্রাইভার কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারি সুবিধাসহ অর্ডার করা যায়।
A4988 কী কাজে লাগে, কেনো করবো?
স্টেপার মোটর ঘুরিয়ে নিখুঁত মুভমেন্ট আনতে এটা লাগে — 3D প্রিন্টার, CNC, প্লটার বা রোবট আর্মে এটাই সবচেয়ে প্রচলিত ড্রাইভার।
Arduino-র সাথে কিভাবে লাগাবো?
VDD-তে 5V আর GND লাগান, STEP ও DIR দুটো ডিজিটাল পিনে দিন, RESET আর SLEEP একসাথে জুড়ুন, এরপর মোটরের চার তার 1A-1B ও 2A-2B পিনে লাগিয়ে কোড থেকে পালস পাঠান।
বোর্ডটা বেশি গরম হচ্ছে, কী করবো?
আগে ট্রিমপট দিয়ে কারেন্ট লিমিট ঠিক করুন, প্রায় 1A-র উপরে হিটসিংক লাগান আর পাওয়ার অন অবস্থায় মোটর খোলা-লাগানো করবেন না — এভাবেই চিপ ঠান্ডা ও নিরাপদ থাকে।