
DC 12V Solenoid Electric Door Lock
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The DC 12V Solenoid Electric Door Lock is a fail-secure latch for DIY access control: with no power the spring holds the plunger out and the door stays locked, and a short 12V pulse pulls the plunger in so the door can open. Drawing around 0.6-0.8A at 12V, it is the actuator inside RFID door locks, PIN-keypad lockers, smart drawers, cabinet latches and small gates.
- Fail-secure: locked when unpowered, opens only while energised
- Coil takes about 8-10W, meant for pulse operation rather than continuous hold
- Two wire leads, coil polarity not critical
- Fit a 1N4007-class flyback diode across the coil terminals
- Metal housing with spring-loaded plunger, about 62 x 41 x 13mm
An Arduino pin cannot drive the coil directly. Switch it through a relay or MOSFET module fed from a real 12V supply of 1A or more.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Rated Voltage: 12 V DC
Working Current: approx 0.6 - 0.8 A at 12V
Power Consumption: approx 8 - 10 W while energized
Action: energize to retract the spring-loaded plunger latch; de-energize returns it to locked
Duty Cycle: intermittent pulse operation — do not hold energized continuously beyond about 30 seconds
Recommended Driver: relay module or MOSFET driver module rated 1 A or more
Flyback Protection: not built in — fit a 1N4007-class diode across the coil terminals
Connection: 2 wire leads, coil polarity not critical
Locking Type: fail-secure (locked when power is absent)
Body: metal housing with spring-loaded plunger
Dimensions: approx 62 x 41 x 13 mm
Applications: RFID/PIN door locks, smart lockers, cabinet and drawer latches, small gates
| Category | Modules |
| Model no. | SOL-LOCK-12V |
| Availability | In stock |
| In stock | 2 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the DC 12V Solenoid Electric Door Lock
What does this solenoid door lock do?
It is an electric latch for light-duty doors: with no power the spring keeps the plunger extended and the door locked, a short 12V pulse pulls the plunger in so the door can open, and removing power locks it again. It is a cabinet, locker and drawer actuator, not a deadbolt for a main entrance.
How do I control it from an Arduino?
Never wire the coil to a GPIO pin. Drive it through a relay module or a MOSFET driver module, with the Arduino pin switching that driver, because the coil draws close to 0.8A, far beyond what a microcontroller pin can supply.
Why is a flyback diode needed and how do I add it?
The coil releases a voltage spike when switched off, which can kill the transistor inside your relay or MOSFET board. Fit a 1N4007 diode across the two lock terminals with the stripe toward the positive lead.
Can the lock stay energised to keep a door open?
No. The coil is built for pulse operation and overheats if held on for minutes. Energise it for a second or two to release the door, then switch it off; the door stays free until it is pushed shut again.
What power supply does it need?
A 12V DC adapter or battery rated 1A or more. Do not run it from the Arduino 5V rail; the voltage is wrong and the current would overload the board's regulator.
RFID বা কিপ্যাড দরজার প্রজেক্টে এটা কী কাজে লাগে?
কার্ড বা কোড মিলে গেলে Arduino রিলে চালু করবে, আর এই লক তখন 12V পেয়ে খুলে যাবে। অর্থাৎ এটাই প্রজেক্টের হাত, যেটা দরজাকে আসলেই খোলে, বাকি সব শুধু সিদ্ধান্ত নেয়।


