Skip to content
Sensors

MQ5 Gas Sensor Module Natural LPG Gas Sensing

৳160

The MQ5 Gas Sensor Module detects LPG, natural gas and coal gas over roughly 200 to 10000 ppm, with the fast response and recovery a leak alarm needs. AO is an analog output for measuring concentration through a microcontroller ADC and DO is a digital output from an LM393 comparator with the threshold set by the onboard potentiometer, so a buzzer alarm can run without any code. Once preheated it reacts quickly to a leak and clears just as fast in fresh air, which suits alarm builds and data logging around a home or a small plant.

  1. Detects LPG, natural gas and coal gas, approx 200-10000 ppm
  2. Fast response and quick recovery once preheated
  3. AO analog output plus DO digital trigger via LM393 comparator
  4. 5V supply, approx 24 h burn-in typical, board about 32 x 22 mm

LPG is heavier than air and settles low, so mount the module near floor level close to the stove or cylinder, not up near the ceiling.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Sensor Type: MQ5 semiconductor gas sensor

Target Gas: LPG, natural gas and coal gas

Detection Range: approx 200-10000 ppm

Operating Voltage: 5V DC (heater and circuit)

Outputs: AO analog output and DO digital output

Comparator: LM393 with onboard potentiometer threshold adjustment

Response: Fast response and recovery (typical for MQ5)

Preheat Time: preheat before use for accurate readings (typical burn-in approx 24 h)

Board Size: approx 32 x 22 mm (typical)

Works With: Arduino ADC, ESP32 ADC, ESP8266 A0

Applications: LPG leak alarms, kitchen safety, gas monitoring IoT nodes

CategorySensors
Model no.MQ5
AvailabilityIn stock
In stock3 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the MQ5 Gas Sensor Module Natural LPG Gas Sensing

What is the MQ5 gas sensor module used for?

It detects LPG, natural gas and coal gas in air from roughly 200 to 10000 ppm, so it is the usual sensor for LPG leak alarms, kitchen safety projects and gas monitoring nodes.

How do I wire it to an Arduino or ESP32?

VCC to 5V and GND to ground, AO to an analog input for concentration readings, and DO to a digital pin for a simple threshold signal. An ESP32 needs the heater on 5V while its 3.3V ADC pin reads AO.

How do I calibrate the threshold?

After full preheat, expose the sensor to the gas level you want to catch, then turn the onboard potentiometer until the DO output just switches. The LED next to it makes the trip point easy to see.

Does it need preheating?

Yes, MQ sensors drift while cold. Give it a warm-up before each use and roughly 24 hours of powered burn-in once, for the most stable long-term behaviour.

How much power does it draw?

The 5V heater dominates consumption, typically in the tens-of-milliamps range, so continuous running is fine from a mains adapter but needs planning on battery.

Any tip for placing it in a real kitchen?

LPG is heavier than air and pools low, so mount the sensor near floor level and close to the stove or cylinder, and test the whole alarm path with a small controlled gas release rather than an open flame.

MQ5 সেন্সরের দাম কত?

এই পেজের ওপরেই সর্বশেষ দাম দেখানো আছে। Contact for price লেখা থাকলে WhatsApp-এ মেসেজ দিন, আজকের রেট জানিয়ে দেবো।