Skip to content
Modules

RC522 RFID Card Reader Module Kit Android NFC supported

৳190

The RC522 RFID card reader module kit is a 13.56MHz MFRC522 reader with a blank MIFARE Classic card and a key fob tag, the standard way to give an Arduino project card-based identity. Bring a tag near the onboard antenna and the reader picks up its UID, or go further and write data into the card's memory blocks for attendance, balance or profile storage. Door access and attendance builds both start here.

  • NXP MFRC522, 13.56MHz, reads ISO14443A and MIFARE Classic tags
  • SPI interface by default, the chip also supports I2C and UART
  • Kit includes the reader, one blank card and one key fob
  • Read range up to about 5cm with the supplied card
  • 3.3V supply only, not 5V tolerant

The classic build is a door lock: the sketch compares the UID against a list and fires a relay to a solenoid latch. An NFC-enabled Android phone reads the same tags, which is handy for checking cards before any wiring.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

CategoryModules
Model no.MFRC522
AvailabilityIn stock
In stock5 pcs
DeliveryCash on Delivery, nationwide Bangladesh
ChipNXP MFRC522 RF transceiver
Carrier Frequency13.56 MHz
Supported TagsISO/IEC 14443A — MIFARE Classic 1K/4K, MIFARE Mini and compatible cards and fobs
Data RateISO14443A up to 424 kbit/s
InterfaceSPI by default (SDA as chip select); chip also supports I2C and UART
Supply Voltage2.5 - 3.6 V DC — 3.3V only, not 5V tolerant
Working Currentapprox 13 - 26 mA idle to active
Read Rangeup to approx 5 cm with the supplied card
Antennaonboard PCB coil antenna
Pins8-pin header — SDA, SCK, MOSI, MISO, IRQ, GND, RST, 3.3V
Kit Contentsreader module, 1 blank MIFARE Classic card, 1 key fob tag
Board Dimensionsapprox 40 x 60 mm
Weightapprox 15 g including card and fob

Customer reviews

No reviews yet — be the first.

Questions about the RC522 RFID Card Reader Module Kit Android NFC supported

What does the RC522 module do?
It is a 13.56MHz RFID reader and writer. It detects a card or fob near the antenna, reads its UID, and can also read or write the card's memory blocks, which is the core of door-access and attendance projects.
How do I connect it to an Arduino UNO?
On the SPI bus: SDA to D10, SCK to D13, MOSI to D11, MISO to D12, RST to D9, GND to GND and 3.3V to the 3.3V pin. Then install the MFRC522 library and run its DumpInfo example to see a card's data.
Can I power it from 5V?
No. The MFRC522 runs on 3.3V and a 5V supply can damage it, so use the Arduino's 3.3V pin. With 3.3V boards like the ESP32 the wiring is direct.
How do I read a card's UID in my sketch?
Call mfrc522.PICC_IsNewCardPresent() and mfrc522.PICC_ReadCardSerial() in the loop, then compare mfrc522.uid.uidByte against your stored list to decide whether to unlock a door or mark attendance.
What are its range and compatibility limits?
Practical range is about 5cm, so tags must come close to the antenna. It reads 13.56MHz ISO14443A tags only, not 125kHz EM4100 ID cards, and it does not emulate a payment card.
RFID দরজা লক প্রজেক্টে এটা কী কাজে লাগে?
কার্ড কাছে নিলে রিডার UID পড়ে, Arduino সেটা অনুমোদিত লিস্টের সাথে মিলিয়ে রিলে চালু করে আর সলিনয়েড লক খুলে দেয়। কিটে কার্ড আর কী-ফব থাকায় টেস্ট করতে অতিরিক্ত কিছু লাগে না।