
0820 Coin Vibration motor (M)
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The 0820 coin vibration motor (M) is an 8 mm flat pancake motor, about 2 mm thick, that turns a 3 V supply into a balanced haptic buzz. Medium sits in the middle of the family: clearly felt through a case or a strap, but without the strong kick of the Large variant, which is why most general-purpose builds settle on it. Two thin wires on the back make it easy to solder to a coin cell holder, a Li-ion rail or a driver board.
- 8 mm diameter, roughly 2 mm thick, fits slim and curved housings
- Rated approx 3 V DC, works from about 2.5 V to 3.5 V
- Draws around 60-100 mA while spinning
- Balanced strength between the L and S variants of the same motor
Run it through a small transistor or driver stage with a flyback diode, never straight off a GPIO pin. Ask us on WhatsApp when you want the whole L/M/S set to compare strengths side by side.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Model: 0820 Coin Vibration motor
Type: Coin / flat ERM (eccentric rotating mass)
Diameter: approx 8 mm
Thickness: approx 2 mm
Rated Voltage: approx 3V DC
Operating Range: approx 2.5-3.5V DC
Current: approx 60-100 mA typical
Vibration Strength: Medium variant — balanced feedback between L and S
Leads: Two thin solderable wires
Drive Method: Transistor or driver stage required, not direct GPIO
Typical Uses: Wearables, phone haptics, toys, alert feedback
| Category | Modules |
| Model no. | CVM-0820-M |
| Availability | In stock |
| In stock | 5 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the 0820 Coin Vibration motor (M)
What is a coin vibration motor used for?
Short haptic buzzes for feedback: notification taps in wearables, button-press confirmation in controllers, alert cues in toys and small devices.
How do I wire it to an Arduino or ESP32?
Through a transistor or MOSFET driver. GPIO to the base or gate via a resistor, the motor in the collector or drain path, and a flyback diode across the motor terminals.
How does the Medium variant compare with L and S?
It sits in the middle: easier to feel than the Small variant, less aggressive than the Large one. Most general-purpose haptics land here.
Which supply voltages suit the Medium variant?
It is rated about 3 V DC and works from roughly 2.5 V to 3.5 V, so two AA cells, a regulated Li-ion rail or a 3.3 V/5 V driver stage can all run it.
এই মোটরের দাম কত?
দাম পেজের ওপরে দেখানো আছে; Contact for price থাকলে WhatsApp-এ জিজ্ঞেস করুন, আমরা আজকের রেট বলে দেবো।
ছোট Li-ion ব্যাটারিতে চলবে কি?
চলবে। মোটরটা প্রায় 2.5-3.5V-এ কাজ করে, তাই 3.7V সেলের সাথে ছোট একটা রেগুলেটর বা ড্রাইভার মডিউল ব্যবহার করলেই যথেষ্ট।


