Skip to content
Modules

2 Channel 5V Relay Board Module

৳145

The 2 channel 5V relay board module carries two independent relays, each with its own optocoupler, status LED and NO, NC and COM screw terminals, so one board switches two separate loads from an Arduino or ESP32. Each input takes 3.3 V or 5 V logic through its optocoupler, keeping the microcontroller side apart from the switched side, and a JD-VCC jumper lets you run the coils from a separate supply when you want full isolation.

  • Two relays, 5 V coils, roughly 70-90 mA each when energised
  • Contacts rated approx 10 A at 250 V AC or 10 A at 30 V DC
  • Optocoupler and status LED on every channel
  • Active-LOW inputs, typical for this design; check the silkscreen before coding

Typical loads: two lights on one controller, a pump plus its valve, or a fan and a lamp in one build. Size motor and heater loads with margin below the contact rating, and cover the mains terminals while powered.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Channels: 2 independent relays

Coil Voltage: 5V DC

Trigger: Active-LOW (typical for this board design)

Input Signal: 3.3V or 5V logic from MCU GPIO

Isolation: Optocoupler per input channel

Contact Rating: approx 10A at 250VAC / 10A at 30VDC

Terminals: NO, NC and COM screw terminals per relay

Indicators: Power LED plus one status LED per channel

JD-VCC Jumper: Remove to power coils from a separate supply

Coil Current: approx 70-90mA per energized relay (typical)

Board Supply: 5V DC

Typical Loads: Lights, fans, pumps, door locks, small appliances

CategoryModules
Model no.RELAY-2CH-5V
AvailabilityIn stock
In stock4 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the 2 Channel 5V Relay Board Module

What is a 2 channel relay board used for?
It lets an Arduino, ESP32 or similar controller switch two separate AC or DC loads — lights, fans, pumps, locks — using only a pair of GPIO pins while keeping the low-voltage electronics isolated from the load side.
How do I connect it to an Arduino or ESP32?
Feed VCC with 5V, tie GND to your controller ground, then run IN1 and IN2 to two GPIO pins; on typical active-LOW boards the relay clicks on when the pin goes LOW, so digitalWrite(pin, LOW) turns the load on.
Will it work with a 3.3V ESP32 board?
Yes in most cases — the optocoupler inputs pull down reliably from a 3.3V GPIO, but the coils themselves must still get 5V, so power the board from a proper 5V source rather than the ESP32's small onboard regulator.
How much current does the board draw?
Around 70-90mA for each energized coil (typical), so a single 5V 1A adapter comfortably runs both channels together with a small microcontroller.
Is this module good for beginners?
It is one of the friendliest ways to learn load switching — screw terminals, labelled LEDs and clear silkscreen markings mean the first project needs no soldering at all.
Relay module or MOSFET module — which should I pick?
Use a relay for mains loads, AC in general, or anywhere you want complete isolation; a MOSFET is the better tool for fast PWM dimming and switching of low-voltage DC loads.
Can it really switch 10A safely?
The contacts are rated approx 10A at 250VAC, but for motors, heaters or long daily service keep the real load well under that figure and stay within what your wiring and enclosure can handle.
2 Channel 5V Relay Board এর দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
রিলে মডিউল অনলাইনে কোথায় কিনবো?
Tekko অনলাইন স্টোরে স্টকে আছে, অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি করা হয়।
হোম অটোমেশনে এটা কী কাজে লাগে, কেনো করবো?
লাইট, ফ্যান, পাম্প বা দরজার লক মোবাইল বা সেন্সর দিয়ে অন-অফ করাতে চাইলে এই দুই চ্যানেল বোর্ডটাই সবচেয়ে সহজ শুরু।
Arduino-র সাথে কিভাবে লাগাবো?
VCC-তে 5V দিন আর GND কমন করুন, তারপর IN1/IN2 পিন GPIO-তে লাগান — এই ধরনের বোর্ড সাধারণত active-LOW, তাই পিন LOW করলেই রিলে অন হয়।
নতুনদের জন্য কোন প্রোজেক্ট দিয়ে শুরু করা ভালো?
মোবাইল-নিয়ন্ত্রিত লাইট কন্ট্রোলার বা সয়ংক্রিয় পানির পাম্প দিয়ে শুরু করুন — স্ক্রু টার্মিনালে তার লাগিয়েই কোড টেস্ট করা যায়, সোল্ডারিং লাগে না।