
3-pin LED (Red & Green)
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
Buy 3-pin LED (Red & Green) at the best price in Bangladesh.
This 3-pin bicolor LED packs a red and a green chip behind one 5mm lens with a shared common pin, so two GPIO lines give you red, green or a blended amber-yellow from a single indicator hole. It is the tidy answer to status panels, traffic-light models, power/OK-fault indicators and any school project where one lamp has to say two things.
Wire the common (centre) leg to ground, drive either side leg through its own series resistor, and switch colours in code - or light both chips together for a third colour. Being a plain through-hole part, it drops into breadboards, hand-etched PCBs and project enclosures without any driver hardware.
Key Features:
• Red and green chips in one 5mm package with a 3-pin layout
• Centre pin common - light either side leg for red or green
• Drive both chips together for an amber/orange blend indicator
• Standard 20mA-class LED: one series resistor per colour is all it needs
• Diffused lens spreads the glow evenly across a panel
• Through-hole legs suit breadboards and hand-soldered PCBs
• Perfect for status panels, traffic-light projects and school electronics
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Type: 3-pin bicolor LED (red + green chips)
Package: 5mm through-hole, diffused lens
Pin Configuration: common pin at centre (typically common cathode)
Forward Voltage (Red): approx 2.0-2.2V at 20mA
Forward Voltage (Green): approx 2.0-2.5V at 20mA
Continuous Current: up to 20mA per chip with a series resistor
Colour Mixing: both chips on together gives an amber/orange appearance
Mounting: through-hole, fits standard 5mm panel holes
Typical Uses: status indicators, traffic-light models, power/fault panels, school projects
| Category | Modules |
| Model no. | LED-5MM-RG3 |
| Availability | In stock |
| In stock | 20 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the 3-pin LED (Red & Green)
What is a 3-pin red-green LED?
Two LED chips (red and green) share one package and one common leg, so with three pins total you can show red, green or both together for an amber blend.
How do I wire it to an Arduino?
Connect the centre (common) leg to GND for a common-cathode part, then each outer leg through its own 220-330Ω resistor to two digital pins; a HIGH pin lights that colour.
How do I know if mine is common cathode or common anode?
Power one outer leg through a resistor and touch the centre leg to GND - if it lights, it is common cathode; if it only lights with the centre leg to +5V, it is common anode and the logic inverts.
What resistor should I use?
Around 220-330Ω per colour from a 5V pin keeps each chip near 20mA safely; on 3.3V boards 100-220Ω is typical.
Can it show other colours?
Red and green at once read as amber/orange - a classic three-state indicator (OK / warning / fault) from one panel hole; PWM on either leg gives in-between shades.
Is it brighter than two separate LEDs?
It saves a panel hole and keeps the colours perfectly aligned in one lens; brightness sits in the normal 5mm LED class and depends on current, not the shared package.
Does it work with 3.3V boards like ESP32?
Yes - both chips light from 3.3V logic through an appropriate resistor; just size the resistors for the lower supply voltage.
৩-পিন LED-এর দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
এটা কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে; অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি হয়।
এক ল্যাম্পেই দুই রঙ - কী কাজে লাগে?
স্ট্যাটাস প্যানেলে একটাই ঘরে সবুজ (ঠিক আছে), লাল (সমস্যা) আর হলুদ-কমলা (সতর্কতা) দেখানো যায় - তিন অবস্থার ইন্ডিকেটরের সবচেয়ে সস্তা উপায় এটা।
বোর্ডে কিভাবে লাগাবো?
মাঝের কমন পাটা GND-তে দিন, দুই পাশের পা দুটো আলাদা ২২০-৩৩০Ω রেজিস্টর দিয়ে দুটো ডিজিটাল পিনে ধরুন - যে পিন HIGH সেই রঙ জ্বলবে।
স্কুল প্রজেক্টে ব্যবহার করা যাবে?
অবশ্যই - ট্রাফিক লাইট মডেল, পাওয়ার ইন্ডিকেটর বা কুইজ গেমের রাউন্ড ইন্ডিকেটর বানাতে এটা শিক্ষার্থীদের প্রিয় কম্পোনেন্ট।


