
DS18B20 Digital Temperature Sensor
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The DS18B20 Digital Temperature Sensor measures -55°C to +125°C and returns a factory-calibrated digital reading over a single data line, accurate to ±0.5°C between -10°C and +85°C.
Because it talks 1-Wire and each sensor carries a unique 64-bit address, one microcontroller pin can read many of them, which is how multi-room monitors, aquarium tank arrays, 3D printer bed logging and greenhouse networks stay cheap and tidy.
- Digital output: no ADC, no analog noise on long runs
- Programmable 9-12 bit resolution, down to 0.0625°C per step
- One 4.7kΩ pull-up on the data line is all the extra wiring
- 3.0-5.5V supply, at home on Arduino, ESP32, ESP8266 and Raspberry Pi setups
- Well supported by the OneWire and DallasTemperature libraries
For aquariums, soil or outdoor installs, the same sensor also comes in a sealed stainless probe version.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Sensor: DS18B20 1-Wire digital temperature sensor
Supply Voltage: 3.0V - 5.5V DC
Interface: 1-Wire digital bus (single data line)
Temperature Range: -55°C to +125°C
Accuracy: ±0.5°C from -10°C to +85°C
Resolution: programmable 9 to 12 bits (0.5°C down to 0.0625°C)
Conversion Time: up to 750 ms at 12-bit resolution
Device Address: unique 64-bit serial code in each sensor
Bus Capacity: multiple sensors on one data line
Pull-up Resistor: 4.7 kΩ from DATA to VCC required
Supply Current: approx 1 mA during conversion, very low when idle
Pins: VCC, DATA (DQ), GND
Compatibility: Arduino, ESP32, ESP8266, STM32, Raspberry Pi (OneWire + DallasTemperature libraries)
Applications: weather stations, aquarium monitors, 3D printers, soil/greenhouse, incubators, cold-chain logging
| Category | Sensors |
| Model no. | DS18B20 |
| Availability | In stock |
| In stock | 2 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the DS18B20 Digital Temperature Sensor
What is a DS18B20 sensor used for?
It measures temperature digitally from -55°C to +125°C and is used in weather stations, aquarium monitors, 3D printers, soil and greenhouse logging, incubators and any project where you want reliable readings without analog noise.
Why use a DS18B20 instead of an LM35 or a thermistor?
The DS18B20 is factory calibrated and outputs a digital value, so there is no ADC requirement, no analog noise creeping in on long wires, and several sensors can share a single microcontroller pin.
How do I connect it to an Arduino?
VCC to 5V or 3.3V, GND to ground, and DATA to any digital pin with a 4.7kΩ resistor between DATA and VCC. The OneWire and DallasTemperature libraries then read the temperature in a few lines of code.
Can I connect more than one DS18B20 to the same pin?
Yes. Every sensor carries a unique 64-bit serial address, so many of them can sit on one data line and be addressed individually.
Is it waterproof?
The bare sensor is a small 3-pin chip. For aquariums, soil or outdoor use, pick the waterproof stainless-steel probe version of the same DS18B20 so the electronics stay sealed.
DS18B20 সেন্সরের দাম কত?
এই পেজের উপরেই সর্বশেষ দাম দেখানো থাকে; Contact for price লেখা থাকলে WhatsApp-এ মেসেজ দিয়ে আজকের রেট জেনে নিন।


