
Gravity: Analog TDS Sensor/Meter for Arduino (SEN0244)
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
Buy Gravity: Analog TDS Sensor/Meter for Arduino (SEN0244) at the best price in Bangladesh.
The DFRobot Gravity TDS sensor is the easiest way to give an Arduino or ESP32 project a reading of total dissolved solids - the number hydroponic growers, aquarium keepers and drinking-water testers care about most. The waterproof probe hangs in the water and the Gravity signal board puts out a clean 0-2.3V analog voltage, so one ADC read plus a little code turns into a ppm value on your display or dashboard. Because it connects with the Gravity 3-pin lead, wiring takes seconds, and the board runs from 3.3V to 5.5V so Leonardo, Uno, Mega and ESP32 boards all work without level shifting.
Use it to watch nutrient strength in a hydroponic reservoir, check whether a filter is pulling its weight in an aquarium, or compare tap, RO and bottled water in a home or school project.
Key Features:
• DFRobot SEN0244 design for measuring TDS in ppm
• Waterproof TDS probe on an attached cable for tanks, reservoirs and cups
• Clean 0-2.3V analog output reads directly on any ADC pin
• Gravity PH2.0-3P connector - plug-and-play with Arduino and ESP32
• Runs from 3.3V to 5.5V, so 3.3V boards work without level shifting
• Ideal for hydroponics, aquariums, RO filter checks and water-quality projects
• Only the probe goes in the water - the board stays dry above the waterline
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Brand/Model: DFRobot SEN0244 (Gravity Analog TDS Sensor/Meter)
Measuring Range: 0-1000 ppm (TDS)
Accuracy: approx ±10% of full scale at 25°C
Operating Voltage: 3.3-5.5V DC
Output Signal: 0-2.3V analog
Connector: Gravity PH2.0-3P (signal, VCC, GND)
Probe: waterproof TDS electrode on attached cable
Probe Cable Length: approx 60cm
Board Size: approx 42 x 30mm
Working Liquid: water-based solutions at room temperature range
Note: the signal board is not waterproof - keep it out of the water
Typical Uses: hydroponics, aquarium monitoring, drinking water and RO testing
| Category | Sensors |
| Model no. | SEN0244 |
| Availability | Out of stock — request notify |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the Gravity: Analog TDS Sensor/Meter for Arduino (SEN0244)
What does this sensor actually measure?
Total dissolved solids (TDS) in ppm - a combined reading of dissolved salts, minerals and impurities, which is the standard quick index of water quality for hydroponics and drinking water.
How do I wire it to an Arduino?
The Gravity 3-pin lead goes to VCC, GND and an analog input; read the pin, then apply the datasheet conversion (with a temperature correction if you also measure water temperature) to get ppm.
Can I use it with a 3.3V ESP32?
Yes - the board accepts 3.3-5.5V and its output stays inside the ADC range of 3.3V boards, one of the main reasons the SEN0244 beat older 5V-only TDS boards.
Does the whole thing go in the water?
No - only the probe end is waterproof; the signal board must stay dry above the waterline.
How accurate is it, and can I trust it for lab work?
About ±10% of full scale at 25°C, right for hobby, farm and educational use; for certified lab analysis you need a bench TDS/conductivity meter instead.
pH sensor or TDS sensor - which do I need?
They answer different questions: pH tells acidity or alkalinity, TDS tells how much dissolved solid is present; serious growers and water testers use both.
How often does it need calibration?
An occasional check against a standard solution (for example 342ppm NaCl) or a trusted reference meter keeps the reading honest; drift is slow in clean-water use.
TDS সেন্সরের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
এটা কোথায় কিনবো?
Tekko অনলাইন স্টোরে স্টকে আছে; অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি হয়।
হাইড্রোপনিক্সে এটা কী কাজে লাগে?
পুষ্টি দ্রবণে কতটা দ্রবীভূত খনি পদার্থ (ppm) আছে দেখিয়ে গাছকে সঠিক মাত্রায় নিউট্রিয়েন্ট দেওয়ার কাজে এটা ব্যবহৃত হয় - অতিরিক্ত বা কম দুটোই ফসলের ক্ষতি করে।
পানিতে কিভাবে লাগাবো?
শুধু প্রোব অংশটা পানিতে ডুবান, বোর্ড পানির বাইরে শুকনো জায়গায় রাখুন; Gravity ৩-পিন তার VCC-GND-আউটপুটে লাগিয়ে Arduino-র ADC পিন থেকে রিডিং নিন।
নতুনরা কি ব্যবহার করতে পারবে?
অবশ্যই - তার লাগানো মাত্র তিনটা কানেকশন আর SEN0244-এর রেডি কোড অনলাইনে পাওয়া যায়, তাই প্রথম প্রজেক্টেই ppm রিডিং পাওয়া কঠিন নয়।


