Skip to content
Sensors

Hall Effect Sensor Module (KY-003)

৳130

The KY-003 hall magnetic sensor is a three-pin module built around the A3144 digital hall-effect switch. Its output changes state when a magnet comes close to the sensing face, and because nothing touches anything else there is no contact bounce and nothing to wear out. That is why makers reach for it for RPM measurement with a magnet on a shaft, door and lid position detection, speedometers and hidden magnetic triggers. It runs from 5V, and on a 3.3V board such as an ESP32 the output level needs checking against the pin rating before you connect it.

  1. A3144 digital hall-effect switch on a small breakout
  2. Digital output that switches when it sees a magnetic field
  3. 5 V supply, three pins: VCC, GND and DO
  4. Contactless sensing, no moving parts
  5. Mounts on a breadboard or project board through the header

Keep the labelled sensing face toward the magnet and mount it within a centimetre or so for a dependable trigger. If it does not fire, flip the magnet around, a hall switch responds to one pole.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Sensor Type: A3144 digital hall-effect switch

Output: Digital, changes state in the presence of a magnetic field

Supply Voltage: 3.3-5 V DC

Pins: 3 (VCC, GND, DO)

Interface: Any MCU GPIO digital input

Detection: Magnetic field from a nearby permanent magnet

Response: Contactless, no contact bounce or wear

Typical Uses: RPM sensing, door and lid position detection, magnetic triggers

Mounting: Through-hole header for breadboard or project board

Polarity Note: Reacts to the matching magnet pole at the sensing face, flip the magnet if no trigger

CategorySensors
Model no.KY-003
AvailabilityIn stock
In stock2 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the Hall Effect Sensor Module (KY-003)

What is the ky-003hall magnetic sensor used for?

It detects the presence of a magnetic field and reports it as a digital signal, so you can count shaft revolutions, detect doors and lids, or fire an event when a hidden magnet passes by.

How do I wire it to an Arduino?

Connect VCC to 5 V (or 3.3 V), GND to ground and DO to any digital input, then read the pin in your sketch or attach an interrupt to count pulses from a spinning magnet.

Can I measure RPM with this module?

Yes — fix a small magnet to the rotating part, count how many times the output switches each second using an interrupt, then convert to RPM based on how many magnets are on the wheel.

Does it work with 3.3 V boards like the ESP32?

Yes, the module runs on 3.3-5 V, so it connects directly to ESP32, ESP8266 and Raspberry Pi GPIO without a level shifter.

Does the sensor need a specific magnet pole?

It responds to one polarity at its sensing face, so if nothing happens simply flip the magnet over and test again from a few millimetres away.

Is it better than a reed switch?

For fast, repetitive switching yes, because the hall element has no contacts to bounce or wear out; a reed switch still wins where you want a fully passive contact that works with no power.

Is this module beginner-friendly?

Very — three wires and a single digitalRead are enough for a first test, which makes it a common choice for a student's first sensor project.

ky-003 hall সেন্সরের দাম কত?

সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস পাবেন।

ঢাকায় এই সেন্সর মডিউল কোথায় পাবো?

Tekko অনলাইন স্টোরে স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারিতে পৌঁছে যাবে।

ম্যাগনেটিক সেন্সর কী কাজে লাগে, কেনো করবো?

চুম্বক কাছে গেলে সিগন্যাল দেয় বলে দরজা খোলা-বন্ধ, RPM মাপা বা লুকানো ট্রিগার বানাতে খুব কাজের, আর যান্ত্রিক সুইচের মতো ক্ষয়ও হয় না।

Arduino-তে কিভাবে লাগাবো?

VCC-তে 5V (বা 3.3V), GND লাগান আর DO পিন যেকোনো ডিজিটাল ইনপুটে দিন — স্কেচে digitalRead করলেই চুম্বক পাওয়া-না-পাওয়া বুঝতে পারবেন।

এই সেন্সর দিয়ে কী কী প্রজেক্ট বানানো যায়?

সাইকেলের স্পিডোমিটার, দরজার অ্যালার্ম, ফ্যানের RPM কাউন্টার বা হিডেন ম্যাগনেট লক — শেখার জন্য চমৎকার সব প্রজেক্ট আইডিয়া।