Skip to content
Modules

I2C Bi-directional Logic Level Converter

৳220

The I2C Bi-directional Logic Level Converter is the small four-channel board that lets 3.3V and 5V parts share one bus without damaging either side. Each channel is a BSS138-style MOSFET that shifts in both directions on its own, with no direction pin to manage, which is exactly what an I2C line needs when a 3.3V ESP32 or Raspberry Pi talks to 5V RTC, OLED and sensor modules.

  1. 4 channels, each shifting in both directions automatically
  2. LV side for 1.8V, 2.8V or 3.3V rails, HV side for 5V
  3. Also fine for SPI, UART and one-wire at moderate speeds
  4. Two rows of 4 pins at 2.54mm pitch
  5. Signal lines only, never for power

Wire LV to 3.3V, HV to 5V and share a ground between the boards, then keep the I2C pull-ups modest so the open-drain bus rises cleanly.

এই part দিয়ে project — কেনার আগে ফ্রি চালিয়ে দেখো:
  • Load Cell Arduino · লঞ্চ নিরাপত্তা মনিটর — ওজন, কাত আর পানির অ্যালার্ম
Tekko Sim — free circuit & Arduino simulator

Channels: 4 bi-directional

Switching Device: BSS138-style MOSFET per channel

Low Side (LV): 1.8V / 2.8V / 3.3V rails, typical

High Side (HV): 5V rails, typical

Direction Control: None required, automatic in both directions

Best Suited: I2C (open-drain) buses

Also Works: SPI, UART, one-wire at moderate speeds

Header: Two rows of 4 pins, 2.54mm pitch

Current Handling: Signal-level currents only, not for power lines

Board Size: approx 15 x 13 mm (typical)

Typical Pairing: ESP32 or Raspberry Pi with 5V sensors and RTC modules

CategoryModules
Model no.LLC-4CH
AvailabilityIn stock
In stock5 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the I2C Bi-directional Logic Level Converter

What is a logic level converter used for?

It safely shifts digital signals between two voltage families — for example letting a 3.3V ESP32 or Raspberry Pi read and drive the pins of a 5V Arduino, OLED, RTC or sensor without over-stressing either chip.

How do I wire it for an I2C bus?

Connect LV to 3.3V and HV to 5V with grounds common, then run SDA from the 3.3V board to a LV-side channel and from the 5V device to the matching HV-side pin; repeat the same pattern for SCL on a second channel.

Is it compatible with Raspberry Pi and ESP32?

Yes — those 3.3V boards are exactly why this module exists, and the LV side also accepts 1.8V devices, so it bridges older low-voltage parts up to 5V systems too.

Does it need its own power supply?

No separate supply — LV and HV simply connect to the existing 3.3V and 5V rails of your project, and the board itself draws only a tiny bias current.

Can a beginner use it without damaging anything?

Yes, as long as LV and HV stay on their correct rails and only signal lines pass through it; swapping the two reference voltages is the one mistake to avoid.

What signals should not go through it?

It is for logic lines only — never run motor current, LED strip power or any supply rail through it, and buses far faster than its comfortable speed range need a dedicated high-speed translator instead.

Why choose MOSFET-based shifting over a resistor divider?

A divider only works one way and slows the edges, while the MOSFET board shifts in both directions — essential for open-drain I2C where either side can pull the line low.

Logic Level Converter এর দাম কত?

সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস থাকে।

এই মডিউল অনলাইনে কোথায় পাবো?

Tekko অনলাইন স্টোরে স্টকে আছে, অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি করা হয়।

3.3V আর 5V বোর্ড জোড়া লাগাতে এটা কী কাজে লাগে, কেনো করবো?

Raspberry Pi বা ESP32-এর 3.3V পিনে সরাসরি 5V সিগন্যাল গেলে পিন নষ্ট হতে পারে, তাই দুই ভোল্টেজ ফ্যামিলির মাঝে নিরাপদে যোগাযোগ করাতে এই ছোট বোর্ডটাই লাগে।

I2C সেন্সরের সাথে কিভাবে লাগাবো?

LV-তে 3.3V আর HV-তে 5V দিন, GND দুই পাশে কমন করুন, তারপর SDA ও SCL আলাদা চ্যানেলে দুই সাইডে লাগিয়ে নিলেই বাস রেডি।

নতুনদের জন্য কোন প্রোজেক্টে ভালো?

Raspberry Pi-এর সাথে Arduino সেন্সর বা RTC মডিউল জুড়ে ওয়েদার স্টেশন বানানো দারুণ শুরু — লেভেল শিফটিং হাতে-কলমে শেখা যায়।