Skip to content
Modules

LM2596 Buck Converter

৳100

The LM2596 Buck Converter steps a higher DC voltage down to whatever a circuit needs: feed 3.2-40V in, turn the onboard multi-turn trimpot, and take a steady 1.25-35V out at up to 2A continuous, 3A peak with heatsinking. At up to 92% efficiency it wastes far less heat than a 7805-style linear regulator, which is why it sits between 12V or 24V batteries, adapters and solar panels and the 5V or 3.3V that Arduino boards, ESP32s, relays, sensors and LED strips actually want.

  • Input 3.2-40V DC, output 1.25-35V adjustable
  • 2A continuous, 3A peak
  • 150kHz LM2596S switching regulator with low ripple
  • Screw terminals on IN and OUT, no soldering to start
  • Output-side LED shows when the rail is live

Two habits worth keeping: measure the output with a multimeter before connecting anything sensitive, and double-check IN+ and IN-, because the module has no reverse-polarity protection.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Model: LM2596 step-down (buck) converter module

Regulator IC: LM2596S-ADJ 150 kHz fixed-frequency PWM switching regulator

Input Voltage: 3.2V - 40V DC

Output Voltage: 1.25V - 35V DC adjustable via onboard multi-turn trimpot

Output Current: 2A continuous, 3A peak (with heatsinking)

Conversion Efficiency: up to 92% (depends on input/output voltage and load)

Switching Frequency: 150 kHz

Output Ripple: approx 30 mV typical with input/output filter capacitors

Terminals: IN+, IN-, OUT+, OUT- screw terminals

Indicator: onboard power LED on the output side

Isolation: non-isolated topology; no reverse-polarity protection — check polarity before connecting

Dimensions: approx 43 x 21 x 14 mm

Weight: approx 14 g

Applications: 12V/24V to 5V/3.3V supply for Arduino, ESP32, relays, LED strips, robot cars, solar projects

CategoryModules
Model no.LM2596S
AvailabilityIn stock
In stock79 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the LM2596 Buck Converter

What does an LM2596 buck converter module do?
It steps a higher DC voltage down to a lower, adjustable one — for example turning a 12V or 24V battery or adapter into a stable 5V or 3.3V supply for microcontrollers, sensors and LEDs.
How do I set the output voltage?
Connect the input source first, measure across OUT+ and OUT- with a multimeter, turn the onboard trimmer until the meter shows the voltage you want, and only then connect your load.
Can it power an Arduino or ESP32 board?
Yes — set it to 5V and feed the Arduino 5V pin, or set 3.3V for an ESP32; with 2A continuous output there is plenty of headroom for a board, display and several sensors at once.
How do I wire it into a project?
Battery or adapter positive goes to IN+ and negative to IN-, your load goes to OUT+ and OUT-, and if a microcontroller is involved keep a common ground between the converter output and the board.
Why choose this over a 7805 linear regulator?
A linear regulator burns the extra voltage as heat, while the LM2596 switches at 150 kHz with up to 92% efficiency, so far less power is wasted and no large heatsink is needed.
Is it suitable for beginners, and what are its limits?
Very beginner friendly thanks to the screw terminals and simple trimmer; just remember it only lowers voltage (it cannot boost), the output must be set before connecting a delicate load, and input polarity must not be reversed.
Can I charge a battery or drive motors with it?
You can run small DC motors, LED strips and loads, but it is not a battery charger and has no current limiting — for charging use a dedicated TP4056 or BMS board.
LM2596 মডিউলের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
অনলাইনে এটা কোথায় পাবো?
Tekko অনলাইন স্টোরে LM2596 বাক কনভার্টার স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারি সুবিধাসহ অর্ডার করা যায়।
ব্যাটারির ভোল্টেজ কমাতে এটা কেনো করবো কেন?
১২V বা ২৪V সোর্স থেকে সহজে ৫V বা ৩.৩V পেতে এর চেয়ে সস্তা ও কার্যকর উপায় নেই — কম তাপ, কম পাওয়ার অপচয়, আর trimpot ঘুরিয়ে যেকোনো ভোল্টেজ সেট করা যায়।
আমার প্রজেক্টে এটা কিভাবে লাগাবো?
IN+ / IN- পাশে ব্যাটারি বা অ্যাডাপ্টার লাগান, মাল্টিমিটার দিয়ে OUT ভোল্টেজ মেপে trimpot ঘুরিয়ে দরকারি ভোল্টেজ সেট করুন, তারপর OUT+ / OUT- থেকে Arduino বা লোডে তার দিন।
Arduino ছাড়া আর কী কাজে লাগে?
LED স্ট্রিপ, রোবট কার, সোলার প্রজেক্ট, মিনি ফ্যান, সার্ভো মোটর আর সব ধরনের ব্যাটারি-চালিত প্রজেক্টে সঠিক ভোল্টেজ দিতে এটা ব্যবহার করা হয় — নতুনদের জন্যও সহজ, কারণ স্ক্রু টার্মিনালে তার লাগালেই চলে।