Skip to content
Sensors

MQ4 Gas Sensor Module Methane CNC Gas Sensing

৳180

The MQ4 Gas Sensor Module is the board to reach for when a project needs to catch methane (CH4) or CNG in the air, over a detection range of roughly 300 to 10000 ppm. AO gives an analog level for measuring concentration through a microcontroller ADC, and DO gives a digital output from an LM393 comparator that trips at a threshold set with the onboard potentiometer. It responds quickly once preheated and clears fast in clean air, which suits kitchen safety demos, gas leak alarms and methane monitoring in labs.

  1. Tuned for methane (CH4) and CNG, approx 300-10000 ppm
  2. AO analog output plus DO digital trigger via LM393 comparator
  3. 5V supply, preheat before use, approx 24 h burn-in typical
  4. Board about 32 x 22 mm

Methane is lighter than air, so mount the module high on the wall near the ceiling rather than beside the burner, and run your buzzer from DO so the alarm still works without code.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Sensor Type: MQ4 semiconductor gas sensor

Target Gas: Methane (CH4) / CNG, with response to some other flammable gases

Detection Range: approx 300-10000 ppm

Operating Voltage: 5V DC (heater and circuit)

Outputs: AO analog output and DO digital output

Comparator: LM393 with onboard potentiometer threshold adjustment

Preheat Time: preheat before use for accurate readings (typical burn-in approx 24 h)

Board Size: approx 32 x 22 mm (typical)

Works With: Arduino ADC, ESP32 ADC, ESP8266 A0

Applications: Gas leak alarms, kitchen safety demos, methane monitoring projects

CategorySensors
Model no.MQ4
AvailabilityIn stock
In stock3 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the MQ4 Gas Sensor Module Methane CNC Gas Sensing

What is the MQ4 gas sensor module used for?

It senses methane (CH4) and CNG in the air over roughly 300 to 10000 ppm, which is what you want for gas leak alarms, kitchen safety projects and methane monitoring.

MQ4 or MQ5 - which one should I pick?

Pick MQ4 when methane and CNG are the target and MQ5 when LPG or natural gas is the target. For a kitchen detector, match the sensor to the gas your stove actually uses.

How do I connect it to an Arduino?

VCC to 5V, GND to ground, AO to an analog input such as A0, and DO to any digital pin if you want a simple threshold signal. Readings rise as methane concentration increases.

How do I set the alarm threshold?

Let the sensor preheat fully, expose it to the concentration you want to react to, then adjust the onboard potentiometer until the DO output and its LED just switch. Anything richer than that now triggers the output.

Does it work with ESP32 and 3.3V boards?

The heater must run from 5V, and the AO signal can be read by a 3.3V ADC pin, so ESP32 and ESP8266 projects work with just that one wiring care point.

How much power does it need, can it run on battery?

The 5V heater dominates the current draw, so continuous battery operation needs a decent supply or a duty-cycle design where the heater switches on only for measurement windows.

রান্নাঘরে কোথায় বসাবো এই সেন্সর?

মিথেন হালকা হয়ে ওপরে ওঠে বলে সেন্সরটা চুলার খুব কাছে নয়, ঘরের ওপরের দিকে বসালে লিক আরও দ্রুত ধরা পড়ে।