Skip to content
Sensors

Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

৳610

Buy Ultrasonic Transducer Waterproof Distance Measuring Sensor Module at the best price in Bangladesh.

This is the waterproof take on the classic HC-SR04: a sealed ultrasonic transducer probe on a cable plus a small control board that speaks the same Trigger/Echo language, so rain, splashes and damp outdoor air no longer stop your distance-measuring project. Point the probe at a water surface, a wall or an approaching vehicle and read centimetres of distance from any Arduino, ESP32 or STM32 - the code you already know from HC-SR04 works almost unchanged.

Typical homes for it are rain-water tank level gauges, pond and reservoir monitoring, outdoor parking assistance and robot navigation in wet or dusty places. Keep the control board dry, let the probe take the weather, and you get steady echo ranging where an open-front HC-SR04 would soon give up.

Key Features:

• Sealed waterproof transducer probe on a cable - built for wet and outdoor duty

• Same Trigger/Echo interface as HC-SR04, so existing sketches port over easily

• 40kHz ultrasonic ranging from roughly 20cm out to 600cm

• 5V supply with a simple high/low echo pulse any microcontroller can time

• Great for water-tank levels, ponds, parking aids and outdoor robots

• 1cm resolution gives practical level and distance readings

• Compact control board fits inside your project enclosure

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Working Voltage: DC 5V

Working Current: approx 30mA

Ultrasonic Frequency: 40kHz

Measuring Range: approx 20-600cm

Resolution: 1cm

Blind Zone: approx 20-25cm

Interface: Trigger and Echo pins (same usage as HC-SR04)

Output Levels: High 5V, Low 0V

Probe: waterproof integrated transducer on attached cable

Sensing Angle: wide cone - keep the probe axis square to the target

Note: keep the control board dry, only the probe is waterproof

Typical Uses: water level measurement, tank gauges, outdoor robots, parking assist

CategorySensors
Model no.JSN-SR04T
AvailabilityOut of stock — request notify
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

How is this different from a regular HC-SR04?

The ultrasonic element lives in a sealed waterproof probe on a cable instead of two exposed cans on the board, so it survives rain, splash and damp locations while working the same Trigger/Echo way.

Can I use my HC-SR04 Arduino code?

Yes - send a 10µs trigger pulse and time the echo width; the timing math is the same, just allow for the slightly larger blind zone of the waterproof probe.

What is the measuring range?

Roughly 20cm to 600cm with 1cm resolution on typical targets; soft or angled surfaces reflect less sound, so keep the probe axis square to what you measure.

Can I put the whole module in water?

No - only the transducer probe is waterproof; the control board must stay in a dry enclosure above the water or outside the wet zone.

How do I measure a tank water level with it?

Mount the probe at the top of the tank pointing straight down, measure the echo distance to the water surface, and subtract from the tank height to get the water depth.

Will it work with ESP32 or ESP8266?

Yes - drive the trigger pin and read the echo as with an HC-SR04; on 3.3V boards use a divider or a 5V-tolerant pin for the 5V echo line.

How accurate is it for level measurement?

Around ±1cm on a calm, flat water surface at moderate distance; ripples, foam and condensation on the probe face are the usual causes of noisy readings.

এই মডিউলের দাম কত?

সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।

অনলাইনে কোথায় পাবো?

Tekko অনলাইন স্টোরে স্টকে আছে; অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি হয়।

পানির ট্যাংকে এটা কী কাজে লাগে?

প্রোব ট্যাংকের উপর থেকে পানির সারফেস পর্যন্ত দূরত্ব মেপে পানির লেভেল বলে দেয় - বৃষ্টিতেও কাজ করে, তাই রিজার্ভ ট্যাংক আর পুকুর মনিটরিংয়ে বহুল ব্যবহৃত।

Arduino-র সাথে কিভাবে লাগাবো?

বোর্ডে 5V-GND দিন, Trig পিনে ১০ মাইক্রোসেকেন্ডের পালস পাঠান, তারপর Echo পিনের পালস প্রস্থ থেকে দূরত্ব বের করুন - HC-SR04-এর মতোই পদ্ধতি।

বাইরের বৃষ্টিতে কি নষ্ট হবে?

প্রোবটা ওয়াটারপ্রুফ, তাই বৃষ্টি আর স্প্ল্যাশ সইতে পারে; শুধু কন্ট্রোল বোর্ডটা ঢাকনার ভেতরে শুকনো রাখতে হবে।