Skip to content
Modules

5V Cooling Fan - 40 x 40 x 10mm

৳120

The 5V cooling fan, 40 x 40 x 10 mm, is a slim brushless axial fan for enclosures and boards that run hot. It draws roughly 0.1-0.2 A from any 5 V rail, turns at about 5000-7000 RPM and moves around 8-10 CFM at a quiet 20-25 dBA. The 40 mm square frame matches the mounting holes most cases already have, and the 2-pin lead wires straight to a 5 V supply or a transistor stage if you want it switched.

  • 40 x 40 x 10 mm brushless DC axial fan, 5 V DC
  • Approx 0.1-0.2 A, 5000-7000 RPM, 8-10 CFM
  • About 20-25 dBA, quiet enough for always-on builds
  • 2-pin connector (some batches 3-pin), leads approx 20-25 cm

Usual spots: over a Raspberry Pi, above a 3D printer mainboard, beside stepper drivers, or moving air through a closed project box. Aim the flow across the hottest component rather than just stirring air, and drive it from a GPIO through a transistor if cooling should follow a temperature sensor.

এই part দিয়ে project — কেনার আগে ফ্রি চালিয়ে দেখো:Tekko Sim — free circuit & Arduino simulator

Frame Size: 40 x 40 x 10 mm

Supply Voltage: 5V DC

Current: approx 0.1-0.2A typical

Type: Brushless DC axial fan

Connector: 2-pin (some batches 3-pin)

Speed: approx 5000-7000 RPM typical

Air Flow: approx 8-10 CFM typical

Noise: approx 20-25 dBA typical

Lead Length: approx 20-25 cm typical

Typical Cooling: Raspberry Pi, 3D printer boards, stepper drivers, enclosures

Mounting: 40mm square frame with holes in each corner

CategoryModules
Model no.FAN-4010-5V
AvailabilityIn stock
In stock3 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the 5V Cooling Fan - 40 x 40 x 10mm

What is this 40mm fan used for?
It moves air across hot electronics — Raspberry Pi processors, 3D-printer mainboards, stepper drivers and power circuits inside closed boxes — preventing thermal throttling and heat-related failures.
How do I power it from a Raspberry Pi or Arduino?
Wire the leads between 5V and ground for always-on cooling, or place a small transistor or MOSFET in the ground path so a GPIO can switch the fan on only when a temperature reading calls for it.
Can it run from a USB power bank or phone charger?
Yes — any source that supplies 5V DC with a spare 200mA or so runs it comfortably.
Is it loud enough to be annoying?
No — at approx 20-25 dBA typical it sits below normal room noise, and slowing it with PWM or a series resistor makes it quieter still.
Is installation beginner-friendly?
Yes — two wires and four mounting holes, and for this brushless model you simply match red to 5V and black to ground.
Which is better for a Pi — this fan or a heatsink alone?
A heatsink spreads heat but still needs airflow in a closed case, so under sustained heavy loads the fan plus a small heatsink combination gives the lowest temperatures.
What should I check before fitting it to my enclosure?
Measure the free space and the screw-hole spacing — this is a 40 x 40 x 10mm frame, so any case drilled for standard 40mm fans accepts it directly.
5V Cooling Fan এর দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস থাকে।
এই ফ্যান কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে, অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি করা হয়।
Raspberry Pi ঠান্ডা রাখতে এটা কী কাজে লাগে, কেনো করবো?
Pi বেশি কাজ করলে গরমে স্লো হয়ে যায়, তাই 40mm ফ্যান বসিয়ে দিলে থ্রটলিং এড়িয়ে পারফরম্যান্স স্থির থাকে — বোর্ডের আয়ুও বাড়ে।
আমার প্রোজেক্টে কিভাবে লাগাবো?
লাল তার 5V-তে আর কালো তার গ্রাউন্ডে দিলেই চলবে; চাইলে ছোট একটা ট্রানজিস্টর দিয়ে GPIO থেকে ফ্যান অন-অফ নিয়ন্ত্রণ করতে পারবেন।
নতুনদের জন্য কোন কাজে দিবে এই ফ্যান?
3D প্রিন্টারের বোর্ড, ক্লোজড Pi কেস বা DIY পাওয়ার সাপ্লাই — যেখানেই গরম জমে সেখানেই এই ছোট ফ্যানটা দরকারি।