Skip to content
Modules

Active Buzzer Module - YL44

৳60

The Active Buzzer Module (YL-44) is an active buzzer on a three-pin board, which means the tone oscillator is built in: give it VCC, ground and a HIGH on the I/O pin and it sounds immediately, with no tone() or PWM code. That single-pin control is why it turns up in timer alarms, water-level alerts, keypad clicks, countdown warnings and parking sensors.

An S8550 transistor on the board does the current switching, so a 3.3V ESP32 or ESP8266 pin can trigger the full 5V buzz through the signal line.

  • 3.3V to 5V supply, about 30mA at most on 5V
  • Pins: VCC, GND, I/O. HIGH sounds, LOW is silent
  • Around 85dB at 10cm on 5V, at the built-in 2.3kHz tone
  • About 19 x 12 x 11mm and 4g, breadboard friendly
  • Works with Arduino UNO/Nano, ESP8266, ESP32, STM32 and PIC

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Module: YL-44 active buzzer breakout

Working Voltage: 3.3V to 5V DC (5V recommended)

Working Current: approx 30 mA max at 5V

Sound Output: approx 85 dB at 10 cm with 5V supply

Tone Frequency: approx 2.3 kHz built-in resonant frequency

Drive Circuit: S8550 PNP transistor on board

Control Signal: HIGH sounds, LOW silent — works from any digital pin

Pins: 3 (VCC, GND, I/O)

Compatible Boards: Arduino UNO/Nano, ESP8266, ESP32, STM32, PIC

Dimensions: approx 19 x 12 x 11 mm

Weight: approx 4 g

CategoryModules
Model no.BUZZER-YL44
AvailabilityOut of stock — request notify
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the Active Buzzer Module - YL44

What is the difference between an active and a passive buzzer?
An active buzzer like this YL-44 carries its own oscillator, so applying DC makes one fixed tone instantly; a passive buzzer needs a PWM or square wave from your code and can then play many frequencies.
How do I connect and code it on an Arduino?
VCC to 5V, GND to GND, and the I/O pin to any digital pin — then digitalWrite(pin, HIGH) sounds it and LOW silences it, with no libraries required.
Can I play melodies on it?
No — an active buzzer produces its single built-in tone only; if you want tunes, siren effects with changing pitch or custom frequencies, pick a passive buzzer instead.
Will it work from an ESP32 or ESP8266?
Yes, that is what the onboard transistor is for — the 3.3V GPIO only drives the signal pin while the buzzer itself runs from 5V, so volume stays full without stressing the microcontroller pin.
How loud is it in practice?
Around 85 dB at close range on 5V, which is enough to hear across a normal room and through a closed project box lid, though volume drops when run on 3.3V.
Where should I use this module in a project?
Anywhere a sound cue beats a display — countdown timers, reverse parking alerts, water-level alarms, keypad feedback, intruder alerts and quiz-game buzzers are the classic uses.
The buzzer sounds weak or stays silent — what should I check?
Confirm VCC really sits at 5V, make sure the signal wire is on the I/O pin rather than swapped with VCC, and remember a floating pin leaves it silent — drive it LOW for off and HIGH for on in code.
Active Buzzer Module YL44 এর দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন — ওখানে সর্বশেষ প্রাইস আপডেট থাকে।
এটা কোথায় পাবো অনলাইনে?
Tekko অনলাইন স্টোরে স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারি সুবিধা নিয়ে অর্ডার করতে পারবেন।
অ্যালার্ম প্রোজেক্টে এটা কেনো করবো?
এক লাইনের কোডেই শব্দ হয়ে যায় — tone বানানোর ঝামেলা নেই, তাই টাইমার, লেভেল অ্যালার্ট বা গেম প্রোজেক্টে সময় বাঁচায়।
Arduino-এর সাথে কিভাবে লাগাবো?
VCC পিন 5V-তে, GND গ্রাউন্ডে আর I/O পিন যেকোনো ডিজিটাল পিনে দিন — digitalWrite HIGH দিলেই বেজে ওঠে, LOW দিলে চুপ।
নতুন শিক্ষার্থীরা কোন কাজে প্রথম ব্যবহার করা ভালো?
কাউন্টডাউন টাইমার বা ওয়াটার লেভেল অ্যালার্ম দিয়ে শুরু করুন — সেন্সর পড়া আর সাউন্ড অ্যালার্ট একসাথে শেখা যায়, আর প্রোজেক্টও দেখতে পূর্ণাঙ্গ লাগে।