Skip to content
Sensors

LDR 5 mm Light Depending Resistor

৳8

The LDR 5 mm light dependent resistor is the classic light sensing component: its resistance drops to a few kilo-ohms in bright light and climbs to around 1 megaohm in darkness. Put it in a voltage divider with a fixed 10k resistor and any analog pin on an Arduino or ESP32 turns the result into a light level reading. That is all a night lamp, line follower, darkness alarm or daylight detector needs, and it has no polarity, needs no library and wires up with two components. It is usually the first sensor in a beginner kit for exactly that reason.

  • 5 mm photoresistor, GL55-style behaviour
  • Bright resistance a few kilo-ohms, dark resistance approx 1 megaohm (typical)
  • No polarity, either lead can go on either side
  • Typical ratings around 150 V and 100 mW
  • Use as a divider with a 10k resistor for ADC input
  • Works with Arduino, ESP32, ESP8266 and bare comparator circuits

If the reading behaves opposite to what you expect, swap the LDR and the resistor positions in the divider.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

CategorySensors
Model no.LDR-5MM
AvailabilityIn stock
In stock20 pcs
DeliveryCash on Delivery, nationwide Bangladesh
ComponentLDR photoresistor (light dependent resistor)
Diameter5 mm
Bright Resistancefew kilo-ohms in bright light (typical)
Dark Resistanceapprox 1 megaohm in darkness (typical)
Max Voltageapprox 150 V (typical rating)
Power Dissipationapprox 100 mW (typical)
PolarityNone - either lead can go on either side
SeriesGL55-style 5 mm LDR (typical behaviour)
UsageVoltage divider with a fixed 10k resistor for ADC input
Works WithArduino, ESP32, ESP8266, comparator circuits
ApplicationsNight lamps, line followers, light alarms, daylight detection

Customer reviews

No reviews yet — be the first.

Questions about the LDR 5 mm Light Depending Resistor

What is an LDR and what is it used for?
A light dependent resistor changes its resistance with the light falling on it, so it is the simplest way for a circuit to tell bright from dark. That covers night lamps, light alarms, line followers and daylight detection.
How do I wire it to an Arduino?
Build a voltage divider: 5V to the LDR, the other LDR leg to an analog pin such as A0, and a 10k resistor from that same pin to GND. analogRead() then rises with light, or falls, depending on which way round you placed the parts.
Is it compatible with ESP32 and 3.3V boards?
Yes, just build the divider from 3.3V instead of 5V so the analog pin never sees more than the board's logic level.
LDR, photodiode or BH1750 - which should I choose?
The LDR is the cheap pick for bright-versus-dark decisions, the BH1750 gives calibrated lux readings over I2C, and photodiodes suit fast pulse work. Choose the LDR when a light level trend is all you need.
অটো নাইট ল্যাম্প বানাতে কিভাবে লাগাবো?
এক পাশ 5V-এ, অন্য পাশ A0-তে, আর A0 থেকে ১০k রেজিস্টর দিয়ে GND-তে লাগান। analogRead() দিয়ে ভ্যালু দেখে একটা থ্রেশহোল্ড ঠিক করুন, তার নিচে পড়লে LED বা রিলে অন করলেই নাইট ল্যাম্প তৈরি।
LDR-এর দাম কত?
এই পেজের ওপরেই সর্বশেষ দাম দেখানো আছে। Contact for price লেখা থাকলে WhatsApp-এ মেসেজ দিন, আজকের রেট জানিয়ে দেবো।