
Regulator Module AMS1117 3.3V
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The AMS1117 3.3V regulator module is a small breadboard breakout that makes a clean, fixed 3.3V rail from a higher DC input. Feed approx 4.5-7V into the input and the onboard AMS1117-3.3 LDO holds the output steady, with input and output capacitors already fitted. It is the board people reach for when a 5V Arduino has to supply ESP8266 or ESP32 Wi-Fi bursts, SD cards, nRF24L01 modules and other 3.3V parts that misbehave on a noisy rail.
- Fixed 3.3V output, recommended input approx 4.5-7V DC
- Up to approx 1A with adequate cooling
- Low-dropout linear regulator, approx 1.1V dropout
- Capacitors on board, breadboard-friendly pins
It is a linear regulator, so keep the input near 5V when you need real current. Dropping 12V to 3.3V at half an amp turns the surplus into heat on the chip, which is buck converter territory.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Output Voltage: 3.3V DC fixed
Regulator IC: AMS1117-3.3
Input Voltage: approx 4.5-7V DC recommended
Maximum Output Current: approx 1A with adequate cooling
Dropout Voltage: approx 1.1V typical
Regulation Type: Low-dropout linear (LDO)
Capacitors: Input and output capacitors onboard
Mounting: Breadboard-friendly through-hole pins
Package: SOT-223 regulator on a small breakout board
Typical Loads: ESP32 / ESP8266, 3.3V sensors, SD card modules, RF links
Thermal Care: Add a small heatsink for high drop or high current
| Category | Modules |
| Model no. | AMS1117-3.3 |
| Availability | In stock |
| In stock | 4 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the Regulator Module AMS1117 3.3V
What is the AMS1117 3.3V module used for?
It creates a steady 3.3V rail from a higher DC source, which is what ESP8266, ESP32, SD cards, nRF24L01 modules and many modern sensors need to run reliably.
How do I wire it into a breadboard project?
Put 5V or any 4.5-7V source on the input pin, connect ground to ground, and take 3.3V from the output pin. The onboard capacitors mean no extra parts are needed for basic use.
Can I power it from an Arduino Uno 5V pin?
Yes, and that is a common setup. The Uno's 5V rail is a good input, and the module then feeds clean 3.3V to sensors that would otherwise be pushed past the Uno's weak onboard 3.3V pin.
How much current can I draw from it?
Up to approx 1A when the chip has adequate cooling. In typical sensor and Wi-Fi projects the real limit is your input supply rather than this board.
How is this different from a buck converter module?
A buck converter wastes less power at large voltage drops and high currents, while this LDO is simpler, smaller and gives cleaner output for sensitive radio and analog parts at modest currents.
3.3V সেন্সর চালাতে এটা কেন লাগবে?
ESP8266, SD কার্ড বা nRF24L01-এর মতো পার্টস অস্থির ভোল্টেজে ঝামেলা করে, তাই পরিষ্কার 3.3V রেইল দেওয়ার জন্য এই মডিউলটা রাখাই নিরাপদ।

