Skip to content
Modules

SSD1306 1.3 inch 128X64 OLED LCD Display

৳600

The SSD1306 1.3 inch 128X64 OLED LCD Display is a monochrome OLED panel with 128 x 64 self-emissive pixels, larger than the common 0.96-inch module and comfortable for sensor dashboards, clocks and multi-line menus. Pixels light themselves, so there is no backlight: the background stays black, text stays sharp from nearly any angle, and the draw sits around 15 to 25 mA at full brightness.

  • I2C on four wires, GND, VCC, SCL and SDA, default address 0x3C
  • Runs from 3.3 to 5V, so it hangs off an Arduino, Nano, ESP8266 or ESP32 directly
  • Works with the Adafruit SSD1306/GFX and U8g2 libraries
  • Some 1.3-inch boards ship with the similar SH1106 driver; if an Adafruit sketch stays blank, use U8g2's SH1106 driver

Two data lines and a library pointed at 0x3C, and your readings show up in sharp pixels.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Display: 1.3 inch monochrome OLED

Resolution: 128 x 64 pixels

Driver IC: SSD1306 (some 1.3-inch boards ship with the similar SH1106 — use U8g2's SH1106 driver if an Adafruit sketch stays blank)

Pixel Colour: white on black (blue on some batches)

Interface: I2C, 2-wire (SCL, SDA)

I2C Address: 0x3C (7-bit) default

Supply Voltage: 3.3 - 5 V DC via onboard regulator

Current Draw: approx 15 - 25 mA at full brightness

Viewing Angle: nearly 180 degrees

Active Area: approx 29.4 x 14.7 mm

Pins: 4-pin header — GND, VCC, SCL, SDA

Operating Temperature: approx -30 to +70 C

Board Dimensions: approx 35 x 34 mm

Weight: approx 8 g

CategoryModules
Model no.SSD1306-13
AvailabilityIn stock
In stock3 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the SSD1306 1.3 inch 128X64 OLED LCD Display

What is this display used for?
Showing live project data — temperature and humidity readings, ultrasonic distance, clock time, menu systems, device status and small graphics. It is the standard faceplate for Arduino and ESP projects that need to talk to a human.
How do I wire it to an Arduino UNO?
VCC to 5V, GND to GND, SCL to A5 and SDA to A4 — that is the UNO's I2C bus. Four jumper wires total, and the same pattern applies to a Nano.
Which library should I use in code?
Install Adafruit SSD1306 plus Adafruit GFX from the Library Manager, call display.begin(SSD1306_SWITCHCAPVCC, 0x3C), then use print and draw calls with display.display() to refresh. U8g2 is the alternative with many more fonts.
My screen stays blank — what is wrong?
First check the wiring and that you passed address 0x3C. If wiring is right, your board most likely uses the SH1106 controller instead of SSD1306 — a common difference on 1.3-inch panels — so try U8g2's SH1106 I2C constructor and it will usually light up.
Does it work with ESP32 and ESP8266?
Yes, natively at 3.3V logic: on ESP32 use SDA 21 and SCL 22, on ESP8266 NodeMCU use D2 for SDA and D1 for SCL, and set the same 0x3C address in the library.
How much power does it need?
About 15-25 mA when fully lit and less with sparse text, from anything between 3.3V and 5V — a board's own regulator or even a small battery supply handles it easily.
Are there any long-term limits I should know?
OLED pixels age: a bright static image left 24/7 can burn in faintly over months. For always-on products, dim the display, invert colours periodically or blank the screen after idle time, and note that at 128 x 64 you have limited space for dense graphics.
১.৩ ইঞ্চি SSD1306 OLED ডিসপ্লের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
এই OLED ডিসপ্লে অনলাইনে কোথায় পাবো?
Tekko অনলাইন স্টোরে 1.3 inch 128x64 OLED স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারি সুবিধায় অর্ডার করতে পারবেন।
সেন্সর প্রজেক্টে এই ডিসপ্লে কী কাজে লাগে?
DHT22-এর তাপমাত্রা-আর্দ্রতা, আলট্রাসনিকের দূরত্ব, ঘড়ির সময় বা রিলের স্ট্যাটাস — সব লাইভ স্ক্রিনে দেখানো যায়, ফলে প্রজেক্ট সিরিয়াল মনিটর ছাড়াই নিজেই কথা বলে, আর পরীক্ষক বা শিক্ষক সামনে ফলাফল দেখতে পান।
Arduino-র সাথে ডিসপ্লেটা কিভাবে লাগাবো?
চার তারেই কাজ শেষ — VCC ৫V, GND গ্রাউন্ড, SCL পিন A5 আর SDA পিন A4; তারপর Adafruit SSD1306 লাইব্রেরি ইনস্টল করে অ্যাড্রেস 0x3C দিয়ে begin করুন, display.display() কল করলেই লেখা স্ক্রিনে চলে আসবে।
০.৯৬ ইঞ্চির সাথে এই ১.৩ ইঞ্চির পার্থক্য কী, নতুনদের জন্য কোনটা ভালো?
১.৩ ইঞ্চিতে পিক্সেল একই থাকলেও প্যানেল বড়, তাই লেখা বেশি আরামদায়ক পড়া যায় — বাজেট ঠিক থাকলে এটাই ভালো বেছে নেওয়া; লাইব্রেরি আর কোড দুই সাইজেই এক, তাই নতুনদের শেখায় কোনো ঝামেলা নেই।