
TP4056 1A Li-ion lithium Battery Charging Module With Current Protection - Type C
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The TP4056 1A Li-ion lithium Battery Charging Module With Current Protection charges a single 3.7V cell from any 5V Type-C source at up to 1A, cutting off at 4.2V. It is the board inside DIY power banks, ESP32 sensor nodes, Bluetooth speakers and handheld Arduino builds, and the DW01 protection IC with its dual MOSFET guards the cell against overcharge, overdischarge, overcurrent and short circuit.
- USB Type-C input, so ordinary phone cables charge the battery
- B+/B- pads for the cell and separate OUT+/OUT- pads for the load
- Charge and standby LEDs show when the battery is full
- Fits 18650, 14500 and Li-Po pouch cells, protected or unprotected
Mount the cell in a proper holder rather than taping wires to it, and feed the module from a 5V source that can genuinely supply 1A.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Charging IC: TP4056
Input: 5V DC via USB Type-C connector
Battery Type: Single-cell 3.7V Li-ion / Li-Po, charges to 4.2V
Charge Current: up to 1A (program current, typical)
Charging Method: Constant current then constant voltage (CC/CV)
Protection: DW01 + dual MOSFET — overcharge, overdischarge, overcurrent, short circuit
Overdischarge Cutoff: approx 2.4V typical
Indicators: Charge LED and standby/full LED (colours vary by batch)
Pads: B+/B- for battery, OUT+/OUT- for load output
Compatible Cells: 18650, 14500, Li-Po pouch, protected or unprotected
Board Size: approx 26 x 17 mm (typical)
Mounting: Through-hole pads for wires and pin headers
| Category | Modules |
| Model no. | TP4056-C |
| Availability | In stock |
| In stock | 40 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the TP4056 1A Li-ion lithium Battery Charging Module With Current Protection - Type C
What does the TP4056 module do?
It charges a single-cell 3.7V lithium battery from any 5V USB source, cutting off at 4.2V, and the DW01 protection circuit also blocks overdischarge and short-circuit currents while the cell powers your project.
How do I wire the battery and the load?
Solder the cell's positive wire to B+ and the negative to B-, take power for your Arduino or ESP32 from OUT+ and OUT-, and plug the Type-C port into a 5V charger to start charging.
Which batteries can I charge with it?
One 18650, 14500 or Li-Po pouch cell at a time. Always a single 3.7V cell, never two in series, and never NiMH or lead-acid chemistry.
How long does a full charge take?
Roughly cell capacity divided by charge current, so a 2000mAh 18650 at 1A finishes in about two to three hours including the slower constant-voltage phase at the end.
Why choose this protected version over the plain TP4056 board?
The DW01 protection lets you use inexpensive unprotected cells with far less risk, which matters inside a sealed enclosure where nobody is watching the cell voltage.
What power supply does it need?
Any 5V USB source rated 1A or more. A weaker port simply charges slower, because the module only draws what the source can give.


