Skip to content
Modules

TCA9548A PCA9548A 8-Way I2C Multiplexer HW-617 Module

৳450

The TCA9548A PCA9548A 8-Way I2C Multiplexer HW-617 Module splits one SDA/SCL pair into 8 independent downstream buses, selected by writing a single byte to its register. It solves the classic address clash: four SSD1306 displays on one Arduino, a row of identical sensors, or a long bus run that kept dropping out until each device group got its own channel.

  1. 8 bidirectional channels, SD0/SC0 through SD7/SC7
  2. Address selectable 0x70 to 0x77 with the A0-A2 jumpers, so eight multiplexers fit on one bus
  3. 1.65 to 5.5V supply lets a 3.3V ESP32 master talk to 5V devices on a channel
  4. 100 kHz and 400 kHz I2C speeds supported

Works with Arduino, ESP32, ESP8266, Raspberry Pi and MicroPython code alike.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Chip: TCA9548A / PCA9548A 8-channel I2C switch

Channels: 8 bidirectional channel pairs, SD0/SC0 to SD7/SC7

I2C Address: 0x70 - 0x77, selected with onboard A0, A1, A2 jumpers

Supply Voltage: 1.65 - 5.5 V DC

Bus Voltage Translation: master and each channel can sit at different logic levels (1.8V / 2.5V / 3.3V / 5V)

Bus Speed: standard 100 kHz and fast-mode 400 kHz supported

Upstream Pins: VIN, GND, SDA, SCL plus A0-A2 address pads

Reset: not broken out on this board — power cycle to clear a stuck channel

Supply Current: a few hundred microamps idle, negligible in projects

Board: HW-617 style breakout with 2.54 mm headers

Dimensions: approx 35 x 21 mm

Weight: approx 4 g

CategoryModules
Model no.HW-617
AvailabilityIn stock
In stock8 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the TCA9548A PCA9548A 8-Way I2C Multiplexer HW-617 Module

What problem does an I2C multiplexer solve?

I2C devices with the same address cannot share one bus — two SSD1306 OLEDs are both at 0x3C and conflict. The TCA9548A gives each its own isolated channel, and you open just the channel you want to talk to.

How do I select a channel in code?

Begin Wire as usual, then write one byte to 0x70: the value 1 opens channel 0, 2 opens channel 1, 4 opens channel 2, and so on as a bit mask. After that every I2C read or write goes to the devices on that channel only; the Adafruit TCA9548A library wraps this in tca.select(0) style calls.

How do I change its I2C address?

The base address is 0x70 and the A0, A1, A2 jumpers each add 1, 2 or 4 — solder or close them to get 0x71 through 0x77. That lets up to 8 multiplexers live on one master bus, giving 64 separate downstream channels.

Can it mix 3.3V and 5V devices on one board?

Yes — that is a hidden strength. The channels are electrically isolated, so a 3.3V ESP32 master can safely drive 5V sensors on a channel, and vice versa; keep each channel's devices at that channel's voltage level.

Are there any speed or topology limits?

Only one channel is connected at a time and switching takes a tiny pause, so it is not for time-critical polling across all channels at once. It only works on I2C — SPI and UART devices do not pass through — and extremely long cable runs still need proper pull-ups.

Which boards and libraries work with it?

Arduino UNO and Nano (A4/A5), ESP8266 (D2/D1), ESP32 (21/22), Raspberry Pi and MicroPython all handle it — it is a plain I2C device, and both the Adafruit TCA9548A Arduino library and U8g2 display support exist.

Is it beginner friendly?

Once you know basic I2C wiring it is very easy — four wires to the master, devices onto the numbered channels, one byte to switch. Most people meet it when a second OLED refuses to work, and the fix is a single library call.

TCA9548A I2C multiplexer মডিউলের দাম কত?

সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।

এই মডিউল অনলাইনে কোথায় কিনবো?

Tekko অনলাইন স্টোরে HW-617 TCA9548A মডিউল স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারি সুবিধায় অর্ডার করতে পারবেন।

একই অ্যাড্রেসের কয়েকটা সেন্সর লাগাতে এটা কেনো করবো কেন?

একই অ্যাড্রেসের দুইটা OLED বা সেন্সর এক বাসে একসাথে চলে না, কিন্তু এই মাল্টিপ্লেক্সার প্রতিটাকে আলাদা চ্যানেলে বসিয়ে কোড থেকে এক লাইনে চ্যানেল বদলে সবগুলো পড়া যায় — অ্যাড্রেস কনফ্লিক্টের সবচেয়ে সহজ সমাধান।

আমার প্রজেক্টে এটা কিভাবে লাগাবো?

VIN, GND, SDA, SCL চার তার Arduino বা ESP32-এর সাথে লাগান, সেন্সরগুলো নম্বর দেওয়া চ্যানেল হেডারে লাগান, তারপর কোডে Wire.beginTransmission(0x70) করে যে চ্যানেল দরকার সেটার বাইট লিখে দিন — ওই চ্যানেলের ডিভাইস তখনই বাসে থাকবে।

কোন কোন প্রজেক্টে এটা বেশি কাজে আসে?

এক সাথে চারটা OLED দিয়ে ডিসপ্লে বোর্ড, গ্রিনহাউসে একই ধরনের একাধিক মাটি সেন্সর, রোবটে বহু IMU মনিটরিং, আর লম্বা তারের বাস আলাদা চ্যানেলে ভেঙে স্থিতিশীল করা — এসব কাজে এই ছোট বোর্ডই প্রজেক্ট বাঁচিয়ে দেয়।