Skip to content
Modules

Vibration Sensor Module

৳85

The Vibration Sensor Module pairs an SW-420 normally-closed vibration switch with an LM393 comparator and outputs a clean digital pulse when the surface it sits on shakes. Bike alarms, door and drawer security triggers, shock logging and motion-activated lights are the usual builds, and it needs only 3.3 to 5V plus one digital pin to work.

  • Onboard potentiometer sets how easily the switch trips
  • Digital output only, no ADC or library required
  • Onboard LED shows the output state while you tune the threshold
  • Works with Arduino, ESP32, ESP8266 and Raspberry Pi GPIO

Bolt it firmly to the surface you want to watch; a loose module senses only itself. Then turn the potentiometer slowly while tapping until the LED trips at the knock strength you want.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Switch Type: SW-420 normally-closed vibration switch

Comparator: LM393

Output: Digital signal that goes active while vibration exceeds the set threshold

Sensitivity: Adjustable via onboard potentiometer

Supply Voltage: 3.3-5V DC

Interface: 3 pins - VCC, GND and digital out (typical pinout)

Indicator: Onboard LED for output state (typical)

Works With: Arduino, ESP32, ESP8266, Raspberry Pi via GPIO

Mounting: Fix firmly to the monitored surface for best response

Applications: Alarms, anti-theft triggers, shock logging, motion detection

CategoryModules
Model no.SW-420
AvailabilityIn stock
In stock5 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the Vibration Sensor Module

What is a vibration sensor module used for?
It detects shaking or impact on the surface it is mounted to and outputs a digital pulse, so it drives anti-theft alarms, door and drawer triggers and shock data loggers.
How do I wire it to an Arduino?
VCC to 5V or 3.3V, GND to ground and the output pin to any digital input; digitalRead() then shows pulses whenever vibration crosses the sensitivity you set.
How do I adjust the sensitivity?
Turn the onboard potentiometer while tapping the surface - set it so the LED just lights on the kind of knock you care about and stays off during ordinary background movement.
Does it work with ESP32 and 3.3V systems?
Yes, the 3.3-5V supply range means it connects directly to ESP32, ESP8266 and other 3.3V boards, and the output can feed an interrupt pin for instant wake-up from deep sleep.
How much power does it use?
Very little in idle - the comparator and switch draw only milliamps, so it can stay powered continuously in battery alarm projects, though a deep-sleep plus interrupt design saves even more.
Is it beginner friendly?
Extremely - three wires, one potentiometer turn and a blink sketch are enough to see it working, which makes it a common first alarm sensor in class projects.
How does it compare with an accelerometer like the MPU-6050?
The MPU-6050 measures how strong a shake is and from which direction, while the SW-420 module simply reports that vibration happened - simpler, cheaper and ideal when you only need a trigger, not a measurement.
ভাইব্রেশন সেন্সর মডিউলের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
এটা কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে, অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি সুবিধা পাবেন।
সিকিউরিটি অ্যালার্মে কেনো করবো কেন?
কেউ ছুঁয়ে নাড়ালেই ডিজিটাল পালস দেয় বলে দরজা, ড্রয়ার বা বাইকের অ্যান্টি-থেফট অ্যালার্মের জন্য এটা সবচেয়ে সহজ ও কম খরচের সেন্সর।
আরডুইনোর সাথে কিভাবে লাগাবো?
VCC 5V-এ, GND গ্রাউন্ডে আর আউটপুট পিন যেকোনো ডিজিটাল পিনে দিন; পটেনশিওমিটার ঘুরিয়ে সেনসিটিভিটি সেট করে digitalRead() দিয়ে টেস্ট করুন।
কোন প্রোজেক্টে ব্যবহার করা যায়?
দরজার অ্যালার্ম, স্কুটার বা বাইকের থেফট অ্যালার্ট, পার্সেল বক্সের শক লগার — নতুনরাও এক বিকেলে বানিয়ে ফেলতে পারে।