Skip to content
Tools & Accessories

18650 3.7V 1200mAH Li-ion Battery Holder (4-Cell)

৳120

The 18650 3.7V 1200mAH Li-ion Battery Holder (4-Cell) seats four 18650 cells in series, making a compact 4S pack with a nominal 14.8V output that rises to about 16.8V straight off the charger. That is the voltage range an L298N or BTS7960 motor driver, a 12V pump or high-torque geared motors want, and you get it without owning a spot welder. Cells are not included.

  • Series 4S layout with a single red and black lead pair to wire
  • Nickel-plated springs hold standard 18 x 65mm cells under tension
  • Approx 2-3A continuous recommended, with a 4S BMS board and a 16.8V charger for charging
  • ABS body with screw holes mounts inside a robot chassis or enclosure

Cells stay removable, so charging and testing happen outside the project.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Cells Held: 4 x 18650 lithium-ion (cells not included)

Compatible Cell: standard 18 x 65mm 18650 including 3.7V 1200mAH

Configuration: series (4S)

Output Voltage: approx 14.8V nominal, about 16.8V fully charged

Contact Material: nickel-plated spring steel

Body Material: ABS plastic

Output Leads: red (+) and black (-), approx 10-15cm

Mounting: screw holes on the holder body

Current Handling: approx 2-3A continuous recommended

Protection Tip: pair with a 4S BMS board and a 16.8V 4S charger

Typical Uses: robot cars, 12V motor drivers, buck converter tests, LED strips

Weight: approx 25-30g

CategoryTools & Accessories
Model no.BH-18650-4S
AvailabilityIn stock
In stock5 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the 18650 3.7V 1200mAH Li-ion Battery Holder (4-Cell)

What does this 4-cell 18650 holder give me?
Four 18650 cells wired in series behave as one 4S pack — roughly 14.8V nominal and about 16.8V fresh off charge — delivered through a single pair of leads.
How do I wire it to a motor driver?
Red lead to the driver's VIN or VM terminal and black to GND, feeding the logic side separately from 5V if the board requires it, and switch on only after double-checking polarity.
Do I need a protection board with it?
Strongly recommended — a 4S BMS stops any single cell drifting too low during discharge, and the pack should only be charged with a proper 16.8V li-ion charger.
Can I use it for Arduino projects?
Yes, but push the raw 14.8V through a buck converter down to 7-12V for the VIN pin rather than ever connecting it near a 5V rail.
What should beginners watch out for?
Polarity and cell matching — insert all four cells the same way round, use cells of similar age and charge level, and never drop an old cell into a fresh series string.
How does it differ from the 1-cell 18650 holder?
The 1-cell cradle outputs one cell's 3.7V for low-voltage builds, while this 4S holder multiplies the voltage four times for motor drivers and 12V-class loads; capacity in amp-hours stays the same either way.
The pack voltage reads low or uneven — what is wrong?
Measure each cell separately, because one weak or self-discharged cell drags the entire series string down; recharge or retire that cell before running the pack again.
18650 3.7V 1200mAH Li-ion Battery Holder (4-Cell) এর দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন — 4S ভার্সনের আপডেটেড প্রাইস ওখানেই দেওয়া থাকে।
বাংলাদেশে এটা কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে, ঢাকা থেকে চট্টগ্রামসহ সারা দেশে হোম ডেলিভারি করা হয়।
রোবট কারে 14.8V দরকার হলে কেনো করবো এটা?
চারটা 18650 সিরিজে বসালেই মোটর ড্রাইভারের দরকারি ভোল্টেজ পাওয়া যায়, আর সেল খোলা যায় বলে চার্জ করাও সহজ থাকে।
সেলগুলো কিভাবে লাগাবো?
প্রতিটা স্লটে + ও - চিহ্ন মিলিয়ে একই দিকে চারটা 18650 বসান, তারপর লাল তার ড্রাইভারের পজিটিভ টার্মিনালে আর কালো তার GND-তে যুক্ত করুন।
নতুন শিক্ষার্থীরা কোন প্রোজেক্টে এটা ব্যবহার শিখবে?
2WD রোবট কার বা L298N মোটর ড্রাইভার দিয়ে শুরু করা ভালো — সাথে 4S BMS আর ঠিক মাপের চার্জার ব্যবহারের অভ্যাসও গড়তে হবে।