
Dev Boards
ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module
৳175
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module is the small 8-pin board that adds 2.4 GHz WiFi to an Arduino project, or runs as a standalone microcontroller once you flash it.
Classic builds: an Uno that talks to your router for a web-controlled relay, a sensor node that posts temperature readings to a server, a soft access point a phone connects to directly. It answers AT commands over UART out of the box, or takes NodeMCU and Arduino firmware through a USB-serial adapter.
- ESP8266EX chip, 802.11 b/g/n at 2.4 GHz, station / soft-AP / both at once
- UART control with AT commands, or your own custom firmware
- 3.0-3.6 V supply only; 5 V damages it, and the RX pin expects 3.3 V logic
- About 70 mA average with higher transmit peaks, so feed it from a proper 3.3 V regulator, not a loaded Uno pin
- Deep sleep support for battery-powered nodes
Pairs well with an ESP-01 adapter board, which handles both the 3.3 V supply and the level shifting for you.
এই part দিয়ে project — কেনার আগে ফ্রি চালিয়ে দেখো:
- Load Cell Arduino · লঞ্চ নিরাপত্তা মনিটর — ওজন, কাত আর পানির অ্যালার্ম
| Category | Dev Boards |
| Model no. | ESP-01 |
| Availability | In stock |
| In stock | 4 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
| Chip | ESP8266EX |
| Wireless Standard | 802.11 b/g/n, 2.4 GHz |
| Network Modes | Station, Soft-AP, Station + Soft-AP |
| Flash Memory | approx 1 MB typical |
| Control Interface | UART (AT commands or custom firmware) |
| Supply Voltage | 3.0-3.6 V DC (5 V will damage the module) |
| Logic Level | 3.3 V |
| Pins | 8-pin header, 2.54 mm pitch |
| Available IO | GPIO0, GPIO2 plus TX/RX |
| Deep Sleep | Supported |
| Antenna | On-board PCB antenna |
| Typical Current | approx 70 mA average, higher peaks while transmitting |
Customer reviews
No reviews yet — be the first.
Questions about the ESP-01 ESP8266 Serial WIFI Wireless Transceiver Module
What is the ESP-01 ESP8266 module used for?
It adds 2.4 GHz WiFi to a project: an Arduino reaches your router through it, or the on-board ESP8266EX runs the whole application as a standalone WiFi microcontroller.
How do I connect the ESP-01 to an Arduino Uno?
Wire VCC and CH_PD (EN) to a clean 3.3 V, GND to ground, then cross-connect TX to the Arduino RX and RX to TX through a voltage divider, and send AT commands from the Serial Monitor at the module's default baud rate.
Can I program the ESP-01 directly instead of using AT commands?
Yes. Pull GPIO0 low while resetting to enter flash mode and upload NodeMCU Lua or Arduino code through a USB-to-serial adapter, after which it runs completely standalone.
How much current does it need?
Plan for roughly 3.3 V at around 70 mA on average with much higher peaks while transmitting, so a weak USB-serial 3.3 V rail or a loaded Uno 3.3 V pin can cause brownouts. Use a proper regulator and a decoupling capacitor.
ESP-01 vs a NodeMCU or ESP-12 board: which should I choose?
Choose the ESP-01 for the fewest pins and the smallest footprint when adding WiFi to an existing Arduino setup; pick a NodeMCU or ESP-12 board when you need more GPIO, analog input and on-board USB.
ESP-01 মডিউলের দাম কত?
এই পেজের ওপরেই বর্তমান দাম দেখানো থাকে; Contact for price লেখা থাকলে WhatsApp-এ মেসেজ দিন, আজকের দাম জানিয়ে দেওয়া হবে।


