
LM35 Waterproof Temperature Sensor
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
The LM35 Waterproof Temperature Sensor is a precision LM35 sealed inside a stainless-steel probe on a three-core cable, so the tip can sit in water, soil, air or inside a machine housing while your board stays dry. Output is a linear 10 mV per degree Celsius, which means no lookup table and no Kelvin offset to subtract: multiply the analog reading and you have degrees C. Accuracy is around ±0.5 °C at room temperature, plenty for student projects and monitoring.
- LM35 die in a sealed stainless-steel probe, waterproof at the tip
- Linear 10 mV per °C output, no calibration needed
- About ±0.5 °C accuracy at 25 °C
- Sensor range roughly -55 to +150 °C at the die, 4-30 V supply
- Three-core cable about 50 cm: supply, signal and ground
- Reads directly on any Arduino, ESP32, STM32 or other ADC input
Typical builds: aquarium monitors, geyser and water heater control, egg incubators, greenhouse soil logging and motor temperature tracking.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Sensor Type: LM35 precision analog temperature sensor in waterproof probe
Output Signal: linear analog voltage, 10 mV per °C
Measurement Range: approx -55°C to +150°C (sensor die)
Accuracy: ±0.5°C typical at 25°C
Supply Voltage: 4V to 30 V DC
Supply Current: less than 60 µA typical
Output Impedance: 0.1 Ω at 1 mA load
Probe Material: sealed stainless-steel tube, waterproof at the tip
Probe Size: approx 6 mm diameter x 25-30 mm length
Cable: 3-core lead (VCC, OUT, GND), approx 50 cm
Scale Factor: 10 mV/°C, no external calibration required
Compatible With: Arduino, ESP32, STM32, PIC and any ADC-based controller
| Category | Sensors |
| Model no. | LM35-WP |
| Availability | In stock |
| In stock | 6 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the LM35 Waterproof Temperature Sensor
What is the LM35 waterproof temperature sensor used for?
It measures temperature by contact and reports it as an analog voltage of 10 mV per °C. The stainless probe tip is sealed, so it can sit in aquarium water, soil, pipes or incubators while your controller stays dry.
How do I wire it to an Arduino and read the temperature?
Connect the supply wire to 5V, ground to GND and the signal wire to A0, then compute temperature as analogRead(A0) times 500.0 divided by 1023.0. On a 3.3V board the multiplier becomes 330.0.
Which part is actually waterproof?
The stainless-steel probe tube and its internal seal. The cable end and any soldered joints are not submersible, so keep splices and the connection to your board out of the liquid.
Can it measure below 0 °C?
The basic LM35 output is 0 V at 0 °C and cannot go negative on a single supply, so sub-zero readings need the negative-bias circuit from the datasheet or a different sensor. For water, soil and weather work the 0-100 °C range normally covers it.
LM35 versus DS18B20 - which should I pick?
The LM35 is analog, needs one ADC channel per probe and the math is one line. The DS18B20 is digital, more noise-immune and many probes share one wire. Pick the LM35 for a single nearby probe, the DS18B20 for long runs or several probes.
LM35 ওয়াটারপ্রুফ প্রোবের দাম কত?
পেজের ওপরেই সর্বশেষ দাম দেখানো আছে। Contact for price থাকলে WhatsApp-এ মেসেজ করলে আজকের রেট জানিয়ে দেবো।


