
MQ-7 Carbon Monoxide Gas Sensor
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
Buy MQ-7 Carbon Monoxide Gas Sensor at the best price in Bangladesh.
The MQ-7 is the hobby-standard sensor for carbon monoxide - the colourless, odourless gas given off where fuel burns, which is exactly why you want one near a gas geyser, kitchen, garage or generator corner. Its tin-dioxide sensing element changes conductivity as CO passes over the heated surface, and the module turns that into both an analog voltage you can chart on an Arduino and a digital output with an adjustable threshold on the onboard comparator.
Give it power and a day or two of preheat, calibrate against clean air and a known CO source if you need numbers in ppm, and you have the front end of a CO alarm, a kitchen safety logger or an air-quality dashboard. Like every MQ sensor it wants sensible placement: ventilated, upright, away from draughts and direct splashes.
Key Features:
• Sensitive to carbon monoxide in the 20-2000ppm band
• SnO2 semiconductor element with built-in heater on a ready-made module
• Dual output: analog A0 for ppm trending, digital D0 with adjustable trip pot
• Works with Arduino, ESP32, ESP8266, STM32 and plain multimeter checks
• Onboard LEDs show power and the digital threshold state
• The recognised core of DIY CO alarms, kitchen safety projects and air-quality loggers
• Low-cost module format with 4 mounting holes for easy panel fitting
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Target Gas: Carbon Monoxide (CO)
Detection Range: 20-2000ppm
Sensing Material: tin dioxide (SnO2) semiconductor
Heater Voltage: 5V (ideal high/low cycle: 60s high, 90s low at 1.4V)
Loop Voltage: up to 10V (typical module operation at 5V)
Outputs: analog A0 and digital D0 with onboard comparator
Threshold: adjustable via onboard potentiometer
Preheat: 24-48 hours recommended for a stable baseline
Board Size: approx 32 x 22mm
Mounting: 4 x through-hole fixing corners
Typical Uses: CO alarms, kitchen/garage safety monitoring, air-quality projects
| Category | Sensors |
| Model no. | MQ-7 |
| Availability | In stock |
| In stock | 3 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the MQ-7 Carbon Monoxide Gas Sensor
What does the MQ-7 detect?
Carbon monoxide - the gas produced by incomplete burning of fuel in geysers, stoves, generators and engines - over roughly 20 to 2000ppm.
How do I read it with an Arduino?
Power the module from 5V, connect A0 to an analog pin and log the voltage; higher CO means higher conductivity and a higher reading once the heater has stabilised.
What is the digital output for?
The onboard comparator compares the analog level with the potentiometer setting and drives D0 high or low, so you can trigger a buzzer or LED at a fixed threshold without any code.
Why does it need preheating?
The heated sensing element drifts until it reaches a stable baseline; burn it in for 24-48 hours when new and give it a few minutes of warm-up each session for consistent readings.
Does the 5V/1.4V heater cycle really matter?
For genuine ppm-level accuracy, yes - the datasheet's 60s-high/90s-low cycle regenerates the element; many hobby projects run constant 5V and accept the trade-off in accuracy.
Can it detect LPG or smoke too?
It reacts somewhat to other combustible gases, but that cross-sensitivity is not dependable; use an MQ-2 for general smoke/LPG work and keep the MQ-7 for CO.
Can a hobby module be used as a real life-safety alarm?
Treat it as a learning and indicator tool; for certified life protection you need a commercial CO alarm that meets safety standards.
MQ-7 সেন্সরের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।
এটা কোথায় কিনবো?
Tekko অনলাইন স্টোরে স্টকে আছে; অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি হয়।
ঘরে এটা কী কাজে লাগে?
গিজার, চুলা বা জেনারেটরের কাছে CO গ্যাস জমলে সেন্সরের রিডিং বেড়ে যায় - DIY CO অ্যালার্ম বা কিচেন সেফটি প্রজেক্টের এটাই মূল যন্ত্র।
Arduino-র সাথে কিভাবে লাগাবো?
মডিউলে 5V-GND দিন, A0 পিন Arduino-র অ্যানালগ ইনপুটে ধরুন; নতুন সেন্সর ২৪-৪৮ ঘণ্টা প্রিহিটে স্থির হয়, তারপর D0 দিয়ে বাজার বা LED চালাতে পারবেন।
নতুন ব্যবহারকারীর জন্য কঠিন কি?
না - তার লাগানো মাত্র চারটা কানেকশন আর MQ-7-এর রেডি লাইব্রেরি/কোড অনলাইনে পাওয়া যায়; শুধু প্রিহিটের ধৈর্যটা রাখতে হয়।


