Skip to content
Modules

pH Sensor Analog Meter Kit E2021-c BNC

৳2220

Buy pH Sensor Analog Meter Kit E2021-c BNC at the best price in Bangladesh.

This pH meter kit pairs a glass combination pH electrode (E2021-C type, BNC connector) with an analog signal board, so any Arduino, ESP32 or other ADC-equipped microcontroller becomes a working pH meter. Dip the probe into aquarium water, hydroponic nutrient solution, drinking water or a lab sample, calibrate once with standard buffer powder, and the board's analog output tracks the full 0-14 pH range. Students use it for chemistry and environmental projects, aquarium keepers watch their tank stability, and rooftop gardeners tune nutrient strength instead of guessing.

The BNC connector keeps the high-impedance electrode lead screened and plug-in simple: push the BNC on, power the board from 5V, and read the output pin with code or a voltmeter. A pH electrode is a consumable, though - keep the glass bulb stored wet and it will give you many months of honest readings.

Key Features:

• Complete kit: E2021-C type glass pH electrode with BNC connector plus analog signal board

• Measures the full 0-14 pH range in water, nutrient solutions and lab samples

• Analog output connects straight to an Arduino ADC pin or a voltmeter

• BNC probe socket keeps the electrode lead screened and easy to replace

• Calibrates in minutes with standard pH 4.00 / 6.86 / 9.18 buffer powder

• Suited to aquariums, hydroponics, drinking water, pools and school labs

• Board runs from a plain 5V supply with no extra parts needed

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Measuring Range: 0-14 pH

Probe Type: E2021-C glass combination pH electrode

Probe Connector: BNC

Board Interface: BNC socket, pin headers for power and output

Signal Board Output: analog voltage proportional to pH

Power Supply: DC 5V

Accuracy: approx ±0.1 pH at 25°C after calibration

Measuring Temperature: 0-60°C

Calibration: two or three point with pH 4.00 / 6.86 / 9.18 buffers

Electrode Cable: fixed BNC lead on the probe

Typical Uses: aquarium, hydroponics, drinking water, pool and lab testing

CategoryModules
Model no.PH-E2021C
AvailabilityOut of stock — request notify
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the pH Sensor Analog Meter Kit E2021-c BNC

What comes with this pH sensor kit?

A glass combination pH electrode of the E2021-C type with a BNC connector, plus the analog signal board that converts the electrode's tiny voltage into a readable output for Arduino, ESP32 or a multimeter.

How do I connect it to an Arduino?

Power the board with 5V and GND, connect its analog output to an ADC pin such as A0, then convert the reading to pH in code after a two-point calibration.

Do I need to calibrate the electrode?

Yes - dissolve standard buffer powder into pH 4.00, 6.86 and 9.18 solutions, rinse the probe between them, and note the board readings so your code can map voltage to pH accurately.

How do I store the pH probe?

Keep the glass bulb wet: cap it with storage or KCl solution between sessions and rinse with distilled water after each test; a dried-out electrode drifts and dies early.

What can I measure with it?

Aquarium water, hydroponic nutrient solution, drinking water, pond and pool water, soil slurry and school chemistry samples - anything water-based within 0-60°C.

Is this the same as a TDS meter?

No - pH shows acidity or alkalinity while TDS shows total dissolved solids; hydroponic growers normally track both because they say different things about the solution.

Is it suitable for a beginner?

Yes, with one care habit: calibration and wet storage. The electrical side is only three wires, so most students get trustworthy numbers on their first calibrated run.

pH Sensor কিটের দাম কত?

সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - ওখানেই আপডেটেড প্রাইস দেওয়া থাকে।

এটা কোথায় পাবো?

Tekko অনলাইন স্টোরে স্টকে আছে; অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি হয়।

পানি পরীক্ষায় এটা কী কাজে লাগে?

আকুরিয়াম, হাইড্রোপনিক্স বা খাওয়ার পানির pH (অ্যাসিডিটি-ক্ষারীয়তা) মেপে জানায় - মাছ আর গাছের জন্য সঠিক pH ধরে রাখার মূল যন্ত্রই এটা।

প্রোবটা কিভাবে লাগাবো?

BNC মাথাটা বোর্ডের সকেটে ঘুরিয়ে লক করুন, বোর্ডে 5V-GND দিন আর আউটপুট পিন Arduino-র A0-তে ধরুন; বাফার দিয়ে ক্যালিব্রেট করলেই রিডিং ব্যবহারের জন্য তৈরি।

প্রোবের যত্ন নেবো কিভাবে?

প্রতিটা টেস্টের পর ডিস্টিলড পানিতে ধুয়ে গ্লাস বাল্ব সবসময় ভেজা রাখুন - স্টোরেজ সলিউশনে ডুবিয়ে রাখলে ইলেকট্রোড মাসের পর মাস ভালো থাকে।