
Screw Terminal 2.54mm 4-Position
- Fresh, latest-batch stock — never old shelf stock
- Tested before it ships
- Arrives dead? We replace it
- Same-day delivery in Dhaka · Cash on Delivery nationwide
- See it before you buy: visit our shop at Ansar Ali Sarak, Boat Ghat, East Nurer Chala, Vatara
Screw terminal block with four positions on a 2.54 mm pitch, the spacing that lands straight on standard perfboard grids and header footprints. Each cage clamp grips a stripped wire under an M2 slotted screw, so external wiring gets a landing point that a screwdriver can release later, with no desoldering involved.
Rated around 2 A per position at 250V, which covers power feeds, sensor field wiring and relay outputs on small builds. For motor or heater loads, move up to a 5.08 mm terminal block instead of paralleling these small clamps.
- 4 positions, top entry, one wire each
- Wire range approx. 28-20 AWG, strip about 5 mm
- Brass tin-plated contacts, PA66 nylon housing, UL94V-0
- Rated approx. 2 A per position at 250V
Seat the block flush on the board, solder one pin, check alignment, then finish the rest.
Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.
Positions: 4 circuits per block
Pitch: 2.54mm pin spacing
Wire Entry: top entry, one wire per position
Wire Range: approx 28-20 AWG (0.08-0.5mm²)
Rated Current: approx 2A per position
Rated Voltage: approx 250V
Contact Material: brass conductor, tin-plated
Screw: M2 slotted plated steel screw
Housing: PA66 nylon, UL94V-0 flame retardant
Pins: brass, tin-plated, through-hole solder pins
Operating Temperature: -40°C to +105°C
Strip Length: approx 5mm bare wire recommended
Typical Uses: power feed, sensor field wiring, relay and driver outputs
Weight: approx 3-4g
| Category | Tools & Accessories |
| Model no. | ST-254-4P |
| Availability | In stock |
| In stock | 50 pcs |
| Delivery | Cash on Delivery, nationwide Bangladesh |
Customer reviews
No reviews yet — be the first.
Questions about the Screw Terminal 2.54mm 4-Position
What is a 4-position 2.54mm screw terminal used for?
It terminates external wires onto a PCB under screw pressure. Power feeds, sensor cables, relay outputs and motor leads all get a serviceable, replaceable connection point.
How do I attach a wire to it?
Strip about 5mm of insulation, push the bare end into the top-entry hole, and tighten the slotted screw clockwise until the wire no longer pulls out by hand.
How much current can one position carry?
Around 2A per position is the sensible rating. For motor or heater loads move up to a larger 5.08mm terminal block instead of paralleling these small clamps.
Can a beginner solder it in cleanly?
Yes. Seat the block flush on the board, solder one pin, re-check alignment, then finish the rest; the plastic body tolerates a normal 350°C iron briefly.
A wire keeps slipping out or the screw will not turn, what now?
Check the wire is stripped long enough and not snagged beside the clamp, back the screw out fully to clear debris, and avoid over-tightening, which strips the M2 thread.
Screw Terminal 2.54mm 4-Position এর দাম কত?
বর্তমান দাম এই পেজের ওপরেই দেখা যায়; Contact for price দেখালে WhatsApp-এ মেসেজ করলে আজকের দাম জানানো হবে।
