Skip to content
Tools & Accessories

18650 3.7V 1200mAH Li-ion Battery Holder (1-Cell)

৳35

The 18650 3.7V 1200mAH Li-ion Battery Holder (1-Cell) is a moulded cradle that holds one 18650 lithium-ion cell, including the common 3.7V 1200mAH size, and turns it into a swappable, rechargeable power source for a build. Cell not included: the holder grips the battery with spring contacts, and the red and black leads drop onto a breadboard rail, a TP4056 charging module or a board's power input.

  • Single-cell 1S layout, 3.7V nominal and roughly 4.2V from a full charge
  • Nickel-plated spring steel contacts with approx 10-15cm lead wires
  • Comfortable around 2-3A continuous, enough for small robot and LED builds
  • Screw holes in the base fix it inside an enclosure

Charge the cell in a proper li-ion charger and never short the contacts while it sits in the holder.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Cells Held: 1 x 18650 lithium-ion (cell not included)

Compatible Cell: 18mm diameter, 65mm length, including 3.7V 1200mAH types

Configuration: single cell (1S)

Output Voltage: 3.7V nominal, approx 4.2V on a full charge

Contact Material: nickel-plated spring steel

Body Material: ABS plastic

Output Leads: red (+) and black (-) wires, approx 10-15cm

Mounting: screw holes on holder base

Current Handling: suitable up to approx 2-3A continuous

Typical Uses: portable Arduino/ESP32 projects, sensor nodes, LED builds

Safety Note: charge cells in a proper li-ion charger, never short the contacts

Weight: approx 8-10g

CategoryTools & Accessories
Model no.BH-18650-1S
AvailabilityIn stock
In stock5 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the 18650 3.7V 1200mAH Li-ion Battery Holder (1-Cell)

What is this 1-cell 18650 holder for?
It cradles a single 18650 lithium cell and exposes its 3.7V output through wires, letting a project run on a removable rechargeable battery instead of a soldered-on cell.
How do I install the battery correctly?
Match the cell's flat negative end to the spring side and the raised positive button to the + marking, then confirm the red lead lands on your circuit's positive rail before powering up.
Is it compatible with a TP4056 charging board?
Yes — connect the holder leads to the B+ and B- pads of a TP4056 module and the same cell charges and discharges through that board safely.
How much current can the holder deliver?
Around 2-3A continuous is a sensible limit; LEDs and small motors are fine, but high-drain builds need spot-welded tabs rather than spring contacts.
Is a beginner safe using loose 18650 cells?
Yes with basic care — never short the terminals, never charge from a random adapter, and use a dedicated li-ion charger or protection board; the holder itself is only a passive cradle.
How does this compare with the 4-cell 18650 holder?
The single-cell cradle keeps a build light at 3.7V, while the 4-cell version stacks four cells in series for about 14.8V — pick whichever matches the voltage your driver or motor actually needs.
The cell fits loosely or the project cuts out — why?
Check that the spring still pushes the cell firmly against the far contact and that no wire has fatigued at the lug; stretching the spring slightly or re-crimping the lead restores contact.
18650 3.7V 1200mAH Li-ion Battery Holder (1-Cell) এর দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন, সিঙ্গেল বা মাল্টিপল পিসের প্রাইস ওখানে আপডেটেড থাকে।
এই 18650 হোল্ডার কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে, সারা বাংলাদেশে হোম ডেলিভারিতে পাঠানো হয়।
পোর্টেবল প্রোজেক্টে এটা কেনো করবো কেন?
সেল সোল্ডার না করে খুলে রিচার্জ করা যায় বলে Arduino বা ESP32 প্রোজেক্টে ব্যাটারি ম্যানেজমেন্ট অনেক সহজ হয়ে যায়।
ব্যাটারি কিভাবে লাগাবো হোল্ডারে?
স্প্রিংওয়ালা দিকে সেলের ফ্ল্যাট নেগেটিভ প্রান্ত আর চিহ্নিত পজিটিভ দিকে বাটন টার্মিনাল বসান, তারপর লাল তার পজিটিভ রেইলে আর কালো তার GND-তে যুক্ত করুন।
নতুনদের জন্য কোন প্রোজেক্ট ভালো হবে এর সাথে?
পোর্টেবল LED ল্যাম্প বা টেম্পারেচার লগার দিয়ে শুরু করুন — TP4056 মডিউলের সাথে জুড়লে চার্জিং অংশটাও হাতে-কলমে শেখা যায়।