Skip to content
Diode

1N5822 Diode

৳26

The 1N5822 Diode is the 3 amp member of the common Schottky family: a 40 V reverse rating and a forward drop of about half a volt, in a DO-201AD axial body with 1.3 mm leads.

It is the usual output rectifier in buck converter modules and homemade DC-DC supplies, the blocking diode between a solar panel and a battery, and the polarity guard on robot and RC battery leads where amps matter and a hot 1N5819 would not survive.

  • 3 A average forward current, 40 V reverse rating
  • Forward drop about 0.525 V max at 3 A
  • No reverse recovery, so switching regulators stay efficient at frequency
  • Survives roughly 150 A non-repetitive surge

At a sustained 3 A the body warms up fast, so keep leads short and give the board some copper around it.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Device: 1N5822 Schottky barrier rectifier diode

Configuration: single axial diode

Average Forward Current: 3 A

Repetitive Reverse Voltage (VRRM): 40 V

Forward Voltage (VF): approx. 0.525 V max at 3 A

Reverse Leakage: higher than silicon diodes, increases with temperature

Switching: essentially no reverse recovery, very fast

Peak Surge Current: approx. 150 A

Package: DO-201AD axial, cathode marked with band

Lead Diameter: approx. 1.3 mm

Typical Uses: buck converter output, solar blocking, reverse polarity protection, battery and RC circuits

CategoryDiode
Model no.1N5822
AvailabilityIn stock
In stock20 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the 1N5822 Diode

What is the 1N5822 used for?
It rectifies or blocks up to 3 A at 40 V with minimal voltage loss, so it shows up in buck converter outputs, solar panel blocking, battery protection paths and reverse polarity guards in robotics and RC builds.
How is it different from the 1N5819?
Same 40 V Schottky character but three times the current - use the 1N5819 up to about 1 A and step up to the 1N5822 when the load runs 1 - 3 A and heat starts to matter.
Why is it preferred in buck converters?
When the switching transistor turns off, this diode carries the full inductor current with under half a volt of drop and no recovery delay, which is what keeps cheap LM2596-class converters efficient and cool.
Can it handle my 200 W solar panel?
A 12 V 200 W panel delivers about 11 A, so no single diode suffices; for a 100 W-class panel at roughly 5 - 6 A, two 1N5822 in parallel or a dedicated high-current Schottky is the right choice.
Does it need a heatsink?
Not usually - at 3 A it dissipates around 1.6 W, which a DO-201AD body sheds with modest airflow; trim the legs long or bond it to metal if your enclosure runs hot.
Is the reverse leakage a problem?
Schottky diodes leak more than silicon ones and the leakage rises with temperature, which is negligible in power paths but worth knowing if you use it in a precision or battery-hungry circuit.
Can I put it on the AC side of a 220 V supply?
No - 40 V reverse rating makes it unusable on mains; reserve it for low-voltage DC systems and converter secondaries, and use 1000 V rectifiers like the 6A10 for mains work.
1N5822 ডায়োডের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - Tekko-তে সেরা দামে পেজে আপডেটেড প্রাইস দেওয়া থাকে।
অনলাইনে এই ডায়োড কোথায় কিনবো?
Tekko অনলাইন স্টোরে স্টকে আছে, অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারিতে দ্রুত পৌঁছে যাবে।
বাক কনভার্টারে এটা কী কাজে লাগে?
বাক কনভার্টারের আউটপুটে এটা ইন্ডাক্টরের কারেন্ট ধরে রাখে - কম ভোল্টেজ ড্রপ আর দ্রুত সুইচিংয়ের কারণে কনভার্টার ঠান্ডা ও দক্ষ থাকে, তাই LM2596 ক্লাসের মডিউলে এটাই লাগে।
সার্কিটে কিভাবে লাগাবো?
দাগের দিক ক্যাথোড - আউটপুট বা প্রোটেকশন পাথে সিরিজে লাগিয়ে দিন আর 3 অ্যাম্পিয়ারের কাছাকাছি লোডে লিড লম্বা রেখে বাতাস চলাচলের সুযোগ দিন।
RC বা রোবটিক্স প্রজেক্টে রাখা ভালো কেন?
ব্যাটারি উল্টো লাগলে পুরো ESC বা মোটর ড্রাইভার নষ্ট হওয়ার আগেই এই ডায়োড সব ব্লক করে দেয়, আর অর্ধেক ভোল্ট ড্রপ হওয়ায় মোটরের শক্তিও কম নষ্ট হয়।