Skip to content
Diode

IR receiver Diode

৳18

The IR receiver diode is a 5 mm photodiode with peak sensitivity at 940 nm, the sensing half of any infrared link you build yourself. Point it at a matching 940 nm IR LED and it becomes the front end of a beam-break alarm, an object counter, a line follower or your own remote-control receiver.

  • Peak response at 940 nm, matched to standard 5 mm IR LEDs
  • Lens-focused viewing angle of roughly +/-20 degrees, so side light is rejected
  • Fast response, suited to pulsed and carrier-frequency IR signals
  • Two-leg through-hole body that sits straight into a breadboard or PCB

A raw photodiode hands you the light signal itself, so the detection logic stays yours: an op-amp, a comparator or an Arduino pin all work as the next stage. Common in school labs and robotics clubs across Bangladesh, usually bought alongside the matching IR LED. Message us on WhatsApp if you want the pair in one order.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Device: 5 mm infrared receiver photodiode

Wavelength (peak): 940 nm

Package: 5 mm diameter molded body, 2 legs (anode and cathode)

Viewing Angle: approx. +/-20 degree lens-focused

Operating Mode: reverse biased for linear photoconductive response

Dark Current: very low, nanoamp class

Response: fast, suitable for carrier-frequency IR signals

Matched Emitter: standard 5 mm 940 nm IR LED

Mounting: through-hole, 2.54 mm typical lead spacing

Typical Uses: IR beam-break alarm, object counting, remote receivers, line following

CategoryDiode
Model no.IR-PD-940
AvailabilityIn stock
In stock20 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the IR receiver Diode

What is an IR receiver diode?
It is a photodiode packaged in a 5 mm lens body that generates current in proportion to the infrared light hitting it, turning invisible IR beams into electrical signals your circuit can process.
How is it different from an IR LED?
The LED emits infrared light while the receiver diode detects it; an easy test is to view any IR LED through your phone camera - glowing purple means it transmits, which is exactly what this diode is designed to receive.
How do I wire it into a circuit?
Reverse-bias it - cathode to positive through a current-limiting resistor, anode toward your sensing node - and read the voltage change across a load resistor with a comparator, op-amp or Arduino analog input.
Can it receive signals from my TV remote?
It sees the 38 kHz carrier flashes the remote sends, but a remote receiver normally uses a TSOP-type demodulator module that decodes the carrier automatically; the raw diode is better when you build your own detection logic.
What projects work well with it?
Beam-break intruder alarms, conveyor object counters, line-following robots paired with IR LEDs, short-range obstacle detection and DIY IR communication links between two Arduinos.
How far can it detect an IR LED?
With matched 940 nm parts and a modest emitter current you get reliable detection from about 5 to 30 cm in ambient light, and several meters in a dark aligned path with lenses; distances vary strongly with alignment and sunlight.
Does sunlight or room light interfere?
Yes, daylight contains IR, so shield the receiver in a small tube, modulate your emitter at a few kHz and detect the modulation - the same trick TV remotes use to ignore lamp light.
IR রিসিভার ডায়োডের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন - Tekko-তে সেরা দামে পেজে আপডেটেড প্রাইস দেওয়া থাকে।
অনলাইনে IR ডায়োড কোথায় কিনবো?
Tekko অনলাইন স্টোরে স্টকে আছে, অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারিতে দ্রুত পৌঁছে যাবে।
এই ডায়োড কী কাজে লাগে?
চোখে না দেখা ইনফ্রারেড আলো ধরে ইলেকট্রিক সিগন্যালে রূপ দেয় - রিমোট রিসিভার, বিম-ব্রেক অ্যালার্ম, অবজেক্ট কাউন্টার বা লাইন ফলোয়িং রোবট বানাতে এটা লাগবেই।
IR LED-র সাথে কিভাবে লাগাবো?
LED আর রিসিভার মুখোমুখি রেখে LED-তে রেজিস্টর দিয়ে কারেন্ট দিন, রিসিভারটা রিভার্স বায়াসে লাগিয়ে তার আউটপুট কম্প্যারেটর বা Arduino-র অ্যানালগ পিনে নিন - বিম কেটে গেলেই সিগন্যাল বদলাবে।
নতুনরা কি সহজে ব্যবহার করতে পারবে?
পারবে - দুই লিগের সাধারণ যন্ত্র, ফোনের ক্যামেরা দিয়ে LED জ্বলছে কি না চেক করে নিলেই লিংক ঠিক করা যায়, তাই প্রথম অপটিক্যাল প্রজেক্টের জন্য আদর্শ।