Skip to content
Capacitors

2.2 uf 50v Capacitor

৳16

The 2.2 uf 50v capacitor is a small-value electrolytic built for timing and coupling rather than bulk storage. Drop it into the RC network of a 555 timer for delays in the seconds range, couple audio between two amplifier stages without passing DC, or calm the reference pin of a regulator. It sits between the small ceramic values and heavier 10uF parts, which is exactly where tone, debounce and delay circuits tend to land.

  • 2.2uF at approx ±20% tolerance, 50V DC
  • Polarized: longer lead positive, stripe marks negative
  • Slim approx 5 x 11 mm body, 2 mm lead spacing
  • Rated -40°C to +105°C, 1000 hour load life

Keep the applied voltage a comfortable step below 50V and watch the polarity on placement. WhatsApp your order and we deliver across Bangladesh, cash on delivery.

Not sure it will work? Test your circuit free in Tekko Sim — on your phone, in Bangla or English.

Capacitance: 2.2uF (2.2 microfarads)

Rated Voltage: 50V DC

Tolerance: approx ±20%

Type: Aluminum Electrolytic

Mounting: Radial Through-Hole

Polarity: Polarized — longer lead is positive, stripe marks negative

Lead Spacing: approx 2mm

Body Size: approx 5mm diameter x 11mm height (typical)

Temperature Range: -40°C to +105°C

Load Life: 1000 hours at rated temperature

Typical Uses: RC timing, 555 delay networks, inter-stage audio coupling, regulator reference filtering

Soldering: Standard iron up to 350°C, brief contact only

CategoryCapacitors
Model no.CAP-2.2UF-50V
AvailabilityIn stock
In stock20 pcs
DeliveryCash on Delivery, nationwide Bangladesh

Customer reviews

No reviews yet — be the first.

Questions about the 2.2 uf 50v Capacitor

What is a 2.2uF 50V capacitor used for?
Mainly timing and coupling — it sets second-scale delays in 555 and RC circuits, carries audio between stages while blocking DC, and filters reference or feedback pins on regulators and op-amps.
How do I use it in a 555 timer circuit?
Wire it from the timing node to ground with the longer positive lead at the node, choose the resistor for the delay you want using t = 1.1 x R x C, and keep the timing pin voltage within the supply range.
Can I put it in a 5V, 9V or 24V circuit?
Yes to all — the 50V rating leaves ample margin on any of those rails, and running an electrolytic well below its rating actually extends its life.
Is it a good part for a first electronics project?
Definitely — a 555 flasher or a one-transistor audio coupling experiment with a 2.2uF part teaches timing math and polarity in a single sitting.
How is 2.2uF different from a 10uF electrolytic?
With the same resistor, 10uF stretches the delay roughly 4.5 times longer; 2.2uF gives snappier timing, a higher bass corner in coupling duty and a smaller footprint.
How long does it last and when should I replace it?
It should serve for thousands of hours at room temperature; replace it when a timer drifts badly, coupling drops the signal level, or the body shows bulging or dried electrolyte.
Does it help with ripple and smoothing?
Only lightly — 2.2uF is far too small for bulk smoothing, but it is exactly right for local reference filtering and keeping fast noise off a single pin.
2.2 uf 50v ক্যাপাসিটরের দাম কত?
সর্বশেষ দাম Tekko প্রোডাক্ট পেজে দেখুন — ওখানেই আপডেটেড প্রাইস পাবেন।
এই ভ্যালুটা কোথায় পাবো?
Tekko অনলাইন স্টোরে স্টকে আছে; অর্ডার করলে সারা বাংলাদেশে হোম ডেলিভারি করা হয়।
টাইমার আর অডিও সার্কিটে এটা কী কাজে লাগে, কেনো করবো?
555 টাইমারের ডিলে ঠিক করতে আর দুই অ্যামপ্লিফায়ার স্টেজের মাঝে DC ব্লক করে অডিও পাঠাতে এই ভ্যালুই বেশি লাগে, তাই টুলবক্সে রাখা দরকার।
ব্রেডবোর্ডে কিভাবে লাগাবো?
লম্বা লিড টাইমিং নোড বা সিগন্যাল পাশে, দাগের লিড গ্রাউন্ডে বসান — ছোট বডির কারণে সরু জায়গাতেও সহজে ঢুকে যায়।
নতুন শিক্ষার্থীরা কী প্রোজেক্ট বানিয়ে শুরু করা ভালো?
555 ফ্ল্যাশার, রিসেট ডিলে সার্কিট বা এক-ট্রানজিস্টর অ্যামপ্লিফায়ার — প্রতিটাতেই ছোট ভ্যালুর ক্যাপাসিটরের ব্যবহার সুন্দরভাবে শেখা যায়।