Tekko BDSimSimulatorProjects

ল্যাবের ডিজিটাল pH মিটারDigital pH Meter with Arduino and LCD (pH Probe)

pH বোর্ডটা AO তে absolute voltage দেয় — pH 7 এ প্রায় 2.5 V, প্রতি pH ধাপে 0.18 V — তাই sketch টা volt কে সরাসরি pH এ ফেরত নেয়। Potentiometer টা আসল pen এর buffer solution দিয়ে করা two-point calibration: মাঝে রাখলে কিছু যোগ হয় না, ঘোরালে দেখানো pH এদিক-ওদিক সরে।

The pH board drives AO with an absolute voltage — about 2.5 V at pH 7, moving 0.18 V per pH step — so the sketch maps volts straight back to pH. The potentiometer stands in for the two-point calibration a real pen gets against buffer solutions: centred it adds nothing, turning it shifts the displayed pH.

▶ ফ্রি চালিয়ে দেখো / Run it free Parts অর্ডার করো (WhatsApp)

সার্কিট ডায়াগ্রাম · Circuit diagram

Digital pH Meter with Arduino and LCD (pH Probe) circuit diagram — Arduino Uno R3, PH sensor module, LCD 16x2 with I2C, Knob (potentiometer), Jumper wires

যা যা লাগবে · Parts you need

তার লাগানো · Wiring

PH sensor module VCC→Arduino Uno R3 5V
PH sensor module GND→Arduino Uno R3 GND
PH sensor module AO→Arduino Uno R3 A0
LCD 16x2 with I2C VCC→Arduino Uno R3 5V
LCD 16x2 with I2C GND→Arduino Uno R3 GND
LCD 16x2 with I2C SDA→Arduino Uno R3 A4
LCD 16x2 with I2C SCL→Arduino Uno R3 A5
Arduino Uno R3 5V→Knob (potentiometer) 1
Knob (potentiometer) 2→Arduino Uno R3 GND
Knob (potentiometer) W→Arduino Uno R3 A1

Code (Arduino C++)

#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27, 16, 2);
// Digital pH meter for the lab: the probe's AO is an ABSOLUTE voltage - about
// 2.5 V at neutral pH 7, moving 0.18 V per pH step (acid higher, alkali
// lower) - so the sketch maps volts straight back to pH. The knob is the
// two-point calibration trim every real pen gets against buffer solutions:
// centred it adds nothing, turning it shifts the displayed pH up or down. The
// verdict line calls the liquid acidic, neutral or basic around the classic
// 6.5 - 7.5 band.
const int PROBE = A0, CAL = A1;

float readPh() {
  float v = analogRead(PROBE) * (5.0 / 1023.0);
  float ph = 7.0 + (2.5 - v) / 0.18;             // probe volts -> pH
  float trim = (analogRead(CAL) * (5.0 / 1023.0) - 2.5) / 0.18;  // knob -> pH offset
  ph += trim;
  if (ph < 0) ph = 0;
  if (ph > 14) ph = 14;
  return ph;
}

void setup() {
  lcd.init();
  lcd.backlight();
  Serial.begin(9600);
}

void loop() {
  float ph = readPh();
  String verdict = "NEUTRAL";
  if (ph < 6.5) verdict = "ACIDIC";
  if (ph > 7.5) verdict = "BASIC";
  lcd.setCursor(0, 0);
  lcd.print("pH: "); lcd.print(ph, 2); lcd.print("       ");
  lcd.setCursor(0, 1);
  lcd.print(verdict);
  lcd.print("                  ");
  Serial.print("pH: "); Serial.print(ph, 2);
  Serial.print(" -> "); Serial.println(verdict);
  delay(300);
}

আরো project · More projects