Tekko BDSimSimulatorProjects

টিডিএস পানির বিশুদ্ধতা পরীক্ষকTDS Water Purity Tester with Arduino (TDS Probe + LCD)

TDS module এর AO পিনে দ্রবীভূত কঠিন পদার্থের সাথে supply এর ভগ্নাংশ বাড়ে, তাই sketch টা analogRead গড় করে volt কে ppm এ ফেরত নিয়ে ব্যান্ডের সাথে মিলিয়ে দেখে। Button চাপলে খাওয়ার পানির ব্যান্ড (~500 ppm এর নিচে) আর মাছের পানির ব্যান্ড (~1000 ppm এর নিচে) বদলায়।

The TDS module's AO pin holds a fraction of the 5 V supply that rises with dissolved solids, so the sketch averages analogRead, converts volts back to ppm and judges the water against a band. The button flips between a drinking band (under ~500 ppm) and a fish-tank band (under ~1000 ppm).

▶ ফ্রি চালিয়ে দেখো / Run it free Parts অর্ডার করো (WhatsApp)

সার্কিট ডায়াগ্রাম · Circuit diagram

TDS Water Purity Tester with Arduino (TDS Probe + LCD) circuit diagram — Arduino Uno R3, TDS water quality sensor, LCD 16x2 with I2C, Push button, Jumper wires

যা যা লাগবে · Parts you need

তার লাগানো · Wiring

TDS water quality sensor VCC→Arduino Uno R3 5V
TDS water quality sensor GND→Arduino Uno R3 GND
TDS water quality sensor AO→Arduino Uno R3 A0
LCD 16x2 with I2C VCC→Arduino Uno R3 5V
LCD 16x2 with I2C GND→Arduino Uno R3 GND
LCD 16x2 with I2C SDA→Arduino Uno R3 A4
LCD 16x2 with I2C SCL→Arduino Uno R3 A5
Push button 1→Arduino Uno R3 D2
Push button 2→Arduino Uno R3 GND

Code (Arduino C++)

#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27, 16, 2);
// TDS water purity tester: the probe's AO pin holds a fraction of the 5 V
// supply - about 0.05 x supply at 0 ppm rising to 0.95 x supply at 1000 ppm.
// The sketch averages the reading, turns it back into ppm, and judges it
// against a band you pick with the button: drinking water (under ~500 ppm) or
// a fish tank (under ~1000 ppm). These are rough demo bands, not a lab
// certificate - the probe cannot say WHICH solids are dissolved.
const int PROBE = A0, BUTTON = 2;
bool fishMode = false, lastBtn = false;   // lastBtn tracks "was pressed"

float readPpm() {
  long sum = 0;
  for (int i = 0; i < 8; i++) { sum += analogRead(PROBE); delay(2); }
  float v = (sum / 8.0) * (5.0 / 1023.0);        // average the samples -> volts
  float ppm = (v - 0.25) / 4.5 * 1000.0;         // 0.25 V = 0 ppm, 4.75 V = 1000 ppm
  if (ppm < 0) ppm = 0;
  return ppm;
}

void setup() {
  pinMode(BUTTON, INPUT_PULLUP);
  lcd.init();
  lcd.backlight();
  Serial.begin(9600);
}

void loop() {
  bool btn = digitalRead(BUTTON) == LOW;
  if (btn && !lastBtn) fishMode = !fishMode;     // one press = one band change
  lastBtn = btn;

  float ppm = readPpm();
  lcd.setCursor(0, 0);
  lcd.print("TDS: "); lcd.print((int)ppm); lcd.print(" ppm     ");
  lcd.setCursor(0, 1);
  if (fishMode) lcd.print(ppm < 1000 ? "Fish OK <1000   " : "Too hard >1000  ");
  else          lcd.print(ppm < 500 ? "Drink OK <500   " : "NOT drinkable   ");
  Serial.print(ppm, 0);
  Serial.println(fishMode ? " ppm (fish band <1000)" : " ppm (drink band <500)");
  delay(300);
}

আরো project · More projects